Wireshark · Wireshark-users: Re: [Wireshark-users] pcap / winpcap filters

["marco\@marcomp\.it" <marco@xxxxxxxxxx>]

Dear Sake,

     I check it also and that's not the issue .....

I think that  the pcap / winpcap filter works only if the packets source or destination ip is in the ethernet inteface subnet range. If it isn't the pcap will discard it without checking it's content.  Could be ?

 

Regards,

Marco

 

 

Da: wireshark-users-bounces@xxxxxxxxxxxxx

A: "Community support list for Wireshark" wireshark-users@xxxxxxxxxxxxx

Cc:

Data: Thu, 29 Apr 2010 17:46:18 +0200

Oggetto: Re: [Wireshark-users] pcap / winpcap filters

> My guess would be that all traffic is vlan-tagged on the mirror port. Could you try the filter "vlan and (port 53 or port 5060)"?

>

> See also: http://wiki.wireshark.org/CaptureSetup/VLAN#head-6bf591391ffef059629a9eede2b4a3d83fdb215d

>

> Cheers,

>

>

> Sake

>

>

> On 29 apr 2010, at 15:37, marco@xxxxxxxxxx wrote:

>

> > Hi Lars,

> > if I do not add any filter I can capture all the traffic ( that do not match as source / destination or both ) the mirroring port send me. While if I enable a filter ( like "igmp" for example )I can only see the traffic that can be accepted by the subnet I configure on my eth interface .....

> >

> > Regards,

> > Marco

> >

> >

> > Da: wireshark-users-bounces@xxxxxxxxxxxxx

> > A: "Community support list for Wireshark" wireshark-users@xxxxxxxxxxxxx

> > Cc:

> > Data: Thu, 29 Apr 2010 15:03:20 +0200

> > Oggetto: Re: [Wireshark-users] pcap / winpcap filters

> >

> > > Hi,

> > > That's not a problem. In **promsicous mode** (checked?), you will see any traffic coming out of the mirror port, regardless if it's on your local subnet or not.

> > > Have you tried sniffing without any filter? Do you see the traffic of the other subnet then?

> > > I suspect your problem is more related to your port mirroring setup than to Wireshark filters.

> > >

> > > Regards,

> > > Lars Ruoff

> > >

> > >

> > > ________________________________________

> > > From: wireshark-users-bounces@xxxxxxxxxxxxx [mailto:wireshark-users-bounces@xxxxxxxxxxxxx] On Behalf Of marco@xxxxxxxxxx

> > > Sent: jeudi 29 avril 2010 14:49

> > > To: wireshark-users@xxxxxxxxxxxxx

> > > Subject: Re: [Wireshark-users] pcap / winpcap filters

> > >

> > > Hi,

> > > yes, that's what I did in the past but if I use this filter string I can only get the packet that lookup on my ethernet interface .... while I need to see all the packets that are not send to / comes from my eth interface subnet .

> > >

> > > I did a port mirroring on a Layer3 switch so on the mirroring port I can see all the packets of some subnet and they will necessary not match my eth interface subnet .....

> > >

> > >

> > > Thanks !

> > > Marco

> > >

> > > Da: wireshark-users-bounces@xxxxxxxxxxxxx

> > > A: "Community support list for Wireshark" wireshark-users@xxxxxxxxxxxxx

> > > Cc:

> > > Data: Thu, 29 Apr 2010 14:09:46 +0200

> > > Oggetto: Re: [Wireshark-users] pcap / winpcap filters

> > >

> > > > Hi,

> > > >

> > > > Would that be a capture filter like: 'port 53 or port 5060'

> > > >

> > > > Thanks,

> > > > Jaap

> > > >

> > > > On Thu, 29 Apr 2010 11:39:17 +0200, "marco\@marcomp\.it"

> > > > wrote:

> > > > > I need to filter some traffic (before capturing it) using the pcap /

> > > > > winpcap filter but this traffic comes from some different subnet (

> > > > > different from my eth interface subnet ).

> > > > > So if I apply a filter the pcap show me the packet that can lookup on my

> > > > > eth interface only ...

> > > > > How can I get the filtered traffic that comes from "everywhere"

> > > > > (0.0.0.0/0) ?

> > > > >

> > > > > I need to filter the data traffic before sending it to whireshark

> > > > because

> > > > > I only need to check the DNS and SIP traffic for a long time ( may be

> > > > for

> > > > > more than 1 week )... so I don't want to store Gbyte and Gbyte of not

> > > > > helpful data on my pc.....

> > > > >

> > > > > Have you any suggestion ?

> > > > >

> > > > >

> > > > > Marco

> > > > >

> > > > subscribe

> > > > ___________________________________________________________________________

> > > > Sent via: Wireshark-users mailing list

> > > > Archives: http://www.wireshark.org/lists/wireshark-users

> > > > Unsubscribe: https://wireshark.org/mailman/options/wireshark-users

> > > > mailto:wireshark-users-request@xxxxxxxxxxxxx?subject=unsubscribe

> > > ___________________________________________________________________________

> > > Sent via: Wireshark-users mailing list

> > > Archives: http://www.wireshark.org/lists/wireshark-users

> > > Unsubscribe: https://wireshark.org/mailman/options/wireshark-users

> > > mailto:wireshark-users-request@xxxxxxxxxxxxx?subject=unsubscribe

> > ___________________________________________________________________________

> > Sent via: Wireshark-users mailing list

> > Archives: http://www.wireshark.org/lists/wireshark-users

> > Unsubscribe: https://wireshark.org/mailman/options/wireshark-users

> > mailto:wireshark-users-request@xxxxxxxxxxxxx?subject=unsubscribe

>

> ___________________________________________________________________________

> Sent via: Wireshark-users mailing list

> Archives: http://www.wireshark.org/lists/wireshark-users

> Unsubscribe: https://wireshark.org/mailman/options/wireshark-users

> mailto:wireshark-users-request@xxxxxxxxxxxxx?subject=unsubscribe