Wireshark · Wireshark-dev: Re: [Wireshark-dev] The cost of memory allocation

[Paul Offord <Paul.Offord@xxxxxxxxxxxx>]

Thanks Graham – that’s a great point and I’ll take a look this evening with a Release build.

 

From: wireshark-dev-bounces@xxxxxxxxxxxxx [mailto:wireshark-dev-bounces@xxxxxxxxxxxxx] On Behalf Of Graham Bloice
Sent: 21 September 2016 10:13
To: Developer support list for Wireshark <wireshark-dev@xxxxxxxxxxxxx>
Subject: Re: [Wireshark-dev] The cost of memory allocation

 

 

 

On 21 September 2016 at 10:06, Paul Offord <Paul.Offord@xxxxxxxxxxxx> wrote:

Good point – debug build.

 

Debug builds using the ms allocator are a lot slower due to all the extra memory checking, i.e. see this page: https://msdn.microsoft.com/en-us/library/974tc9t1.aspx

 

I'm not entirely certain though, that a debug build of Wireshark will use a version of glib that then uses the debug calls into msvcrt.

 

However the point still stands, that using debug builds for performance testing might not be giving you the real picture.

 

 

From: wireshark-dev-bounces@xxxxxxxxxxxxx [mailto:wireshark-dev-bounces@xxxxxxxxxxxxx] On Behalf Of Graham Bloice
Sent: 21 September 2016 09:49
To: Developer support list for Wireshark <wireshark-dev@xxxxxxxxxxxxx>
Subject: Re: [Wireshark-dev] The cost of memory allocation

 

 

 

On 21 September 2016 at 09:29, Paul Offord <Paul.Offord@xxxxxxxxxxxx> wrote:

I’m not happy with the performance of the transum dissector and so I’ve started some analysis.  I’ve never used VS performance profiling before but I plan try to investigate this problem using it.  In the meantime I’ve used a tool that I’m reasonably familiar with called PerfView.  It’s produced some interesting results which I thought I’d share.

 

The problem I’m having is that with transum enabled load time for a 50MB file increases from 5 seconds to 10 seconds, but then subsequent loads of the same file go out to about 40 or 50 seconds.

 

 

Above (or attached depending on your email system) is a screen shot showing the time spent in various functions when a load of the file took 44.8 seconds.  At the top of the image is a transum function called decode_gtcp.  The image shows that 50.7% of the total load time was spent executing in this function.  Then we see all of the nested functions with the proportion of time spent in each of those.

 

What I notice is that a lot of time is being spent in glib functions, and in particular the time is being spent allocating and freeing memory.

 

 

Using a slightly different view we can see that across the whole of the process during a load file with transum enabled more than 66% of the time is spent messing around with memory.

 

I haven’t yet figured out why I get inconsistent load times, and I don’t know what I can do about any of the above, but I thought it might be of general interest.

 

Best regards…Paul

 

 

Release or debug build?

 

--

Graham Bloice

______________________________________________________________________

This message contains confidential information and is intended only for the individual named. If you are not the named addressee you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately by e-mail if you have received this e-mail by mistake and delete this e-mail from your system.

Any views or opinions expressed are solely those of the author and do not necessarily represent those of Advance Seven Ltd. E-mail transmission cannot be guaranteed to be secure or error-free as information could be intercepted, corrupted, lost, destroyed, arrive late or incomplete, or contain viruses. The sender therefore does not accept liability for any errors or omissions in the contents of this message, which arise as a result of e-mail transmission.

Advance Seven Ltd. Registered in England & Wales numbered 2373877 at Endeavour House, Coopers End Lane, Stansted, Essex CM24 1SJ

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please visit http://www.symanteccloud.com
______________________________________________________________________

___________________________________________________________________________
Sent via:    Wireshark-dev mailing list <wireshark-dev@xxxxxxxxxxxxx>
Archives:    https://www.wireshark.org/lists/wireshark-dev
Unsubscribe: https://www.wireshark.org/mailman/options/wireshark-dev
             mailto:wireshark-dev-request@xxxxxxxxxxxxx?subject=unsubscribe

 

--

Graham Bloice

Software Developer

Trihedral UK Limited

______________________________________________________________________

This message contains confidential information and is intended only for the individual named. If you are not the named addressee you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately by e-mail if you have received this e-mail by mistake and delete this e-mail from your system.

Any views or opinions expressed are solely those of the author and do not necessarily represent those of Advance Seven Ltd. E-mail transmission cannot be guaranteed to be secure or error-free as information could be intercepted, corrupted, lost, destroyed, arrive late or incomplete, or contain viruses. The sender therefore does not accept liability for any errors or omissions in the contents of this message, which arise as a result of e-mail transmission.

Advance Seven Ltd. Registered in England & Wales numbered 2373877 at Endeavour House, Coopers End Lane, Stansted, Essex CM24 1SJ

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please visit http://www.symanteccloud.com
______________________________________________________________________