Ethereal-dev: [Ethereal-dev] Re: Patch for new dissector plugin for Ether-S-Bus telegrams modi
Note: This archive is from the project's previous web site, ethereal.com. This list is no longer active.
From: Christian Durrer <Christian.durrer@xxxxxxxxxxxx>
Date: Thu, 15 Jun 2006 20:24:50 +0200
Hi, thank you for your feedback. I finally managed to modify my code by - using symbols instead of hardcoded command codes - removing the debug code - removing the last set in the patch - adding the Makefile.common in the plugins dir Could you please have a look at it and if it is ok, check it in? Thanx, chris On Sun, 2006-06-04 at 12:00 -0500, ethereal-dev-request@xxxxxxxxxxxx wrote: > Send Ethereal-dev mailing list submissions to > ethereal-dev@xxxxxxxxxxxx > > To subscribe or unsubscribe via the World Wide Web, visit > http://www.ethereal.com/mailman/listinfo/ethereal-dev > or, via email, send a message with subject or body 'help' to > ethereal-dev-request@xxxxxxxxxxxx > > You can reach the person managing the list at > ethereal-dev-owner@xxxxxxxxxxxx > > When replying, please edit your Subject line so it is more specific > than "Re: Contents of Ethereal-dev digest..." > > > Reply-To: Ethereal development <ethereal-dev@xxxxxxxxxxxx> > > Today's Topics: > > 1. Re: Patch for new dissector plugin for Ether-S-Bus telegrams > (Jaap Keuter) > 2. Re: ieee802.11 AID calculation patch (Joerg Mayer) > 3. one more h245/per alignment issue (Cvetan Ivanov) > > > ---------------------------------------------------------------------- > > Message: 1 > Date: Sun, 4 Jun 2006 13:32:17 +0200 (CEST) > From: Jaap Keuter <jaap.keuter@xxxxxxxxx> > Subject: Re: [Ethereal-dev] Patch for new dissector plugin for > Ether-S-Bus telegrams > To: Ethereal development <ethereal-dev@xxxxxxxxxxxx> > Message-ID: <20060604131759.K47378-100000@xxxxxxxxxxxxx> > Content-Type: TEXT/PLAIN; charset=US-ASCII > > Hi, > > This looks pretty good, thanks. > > A few small remark though: > 1. could you use meaningfull symbols in the code i.s.o. hardcoded values. > I'm refering to code like this: > > + if (((request_val->cmd_code) == 0x00) || > + ((request_val->cmd_code) == 0x06) || > + ((request_val->cmd_code) == 0x07) || > + ((request_val->cmd_code) == 0x1E) || > + ((request_val->cmd_code) == 0x1F) || > + ((request_val->cmd_code) == 0xA1)){ > > 2. Could you clean up the code a bit by removing the debug code from it > > 3. The last change in the set is superflous. > > Thanx, > Jaap > > > > On Sat, 3 Jun 2006, Christian Durrer wrote: > > > Hi, > > > > I hope this is the right place to send a patch for a new dissector > > plugin. The telegram it dissects are for the communication between PLCs > > (Programmable logic controller) from the company Saia Burgess Controls > > Ltd. (http://www.start-controls.com, http://www.saia-burgess.com or > > http://www.sbc-support.ch). The protocol is named Ether-S-Bus (the PLCs > > are called PCD2, PCD3, PCD4). > > We developped this dissector for easyer debugging of networks containing > > our contollers. > > > > The patch was created against Ethereal Version 1.1.0 (SVN Rev 18189). I > > tested it with various capture files (which some of them also fuzzed). > > The VariousSBus is one of them. > > > > I also would like to make you a big compliment! Ethereal is a great > > tool! > > > > I'm available for any your questions > > > > With best regards > > > > Christian Durrer > > > > End of Ethereal-dev Digest, Vol 38, Issue 7 > *******************************************
Index: /ethereal/configure.in
===================================================================
--- /ethereal/configure.in (revision 18189)
+++ /ethereal/configure.in (working copy)
@@ -1340,6 +1340,7 @@
plugins/rlm/Makefile
plugins/rtnet/Makefile
plugins/rudp/Makefile
+ plugins/sbus/Makefile
plugins/stats_tree/Makefile
plugins/v5ua/Makefile
tools/Makefile
Index: /ethereal/Makefile.am
===================================================================
--- /ethereal/Makefile.am (revision 18189)
+++ /ethereal/Makefile.am (working copy)
@@ -209,6 +209,7 @@
plugins/rlm/rlm.la \
plugins/rtnet/rtnet.la \
plugins/rudp/rudp.la \
+ plugins/sbus/sbus.la \
plugins/stats_tree/stats_tree.la \
plugins/v5ua/v5ua.la
@@ -249,6 +250,7 @@
"-dlopen" plugins/rlm/rlm.la \
"-dlopen" plugins/rtnet/rtnet.la \
"-dlopen" plugins/rudp/rudp.la \
+ "-dlopen" plugins/sbus/sbus.la \
"-dlopen" plugins/stats_tree/stats_tree.la \
"-dlopen" plugins/v5ua/v5ua.la
Index: /ethereal/plugins/Makefile.nmake
===================================================================
--- /ethereal/plugins/Makefile.nmake (revision 18189)
+++ /ethereal/plugins/Makefile.nmake (working copy)
@@ -30,6 +30,7 @@
rlm \
rtnet \
rudp \
+ sbus \
stats_tree \
v5ua
@@ -151,6 +152,11 @@
$(MAKE) /$(MAKEFLAGS) -f Makefile.nmake
cd ..
+sbus::
+ cd sbus
+ $(MAKE) /$(MAKEFLAGS) -f Makefile.nmake
+ cd ..
+
stats_tree::
cd stats_tree
$(MAKE) /$(MAKEFLAGS) -f Makefile.nmake
@@ -209,6 +215,8 @@
$(MAKE) /$(MAKEFLAGS) -f Makefile.nmake clean
cd ../rudp
$(MAKE) /$(MAKEFLAGS) -f Makefile.nmake clean
+ cd ../sbus
+ $(MAKE) /$(MAKEFLAGS) -f Makefile.nmake clean
cd ../stats_tree
$(MAKE) /$(MAKEFLAGS) -f Makefile.nmake clean
cd ../v5ua
@@ -262,6 +270,8 @@
$(MAKE) /$(MAKEFLAGS) -f Makefile.nmake distclean
cd ../rudp
$(MAKE) /$(MAKEFLAGS) -f Makefile.nmake distclean
+ cd ../sbus
+ $(MAKE) /$(MAKEFLAGS) -f Makefile.nmake distclean
cd ../stats_tree
$(MAKE) /$(MAKEFLAGS) -f Makefile.nmake distclean
cd ../v5ua
@@ -313,6 +323,8 @@
$(MAKE) /$(MAKEFLAGS) -f Makefile.nmake maintainer-clean
cd ../rudp
$(MAKE) /$(MAKEFLAGS) -f Makefile.nmake maintainer-clean
+ cd ../sbus
+ $(MAKE) /$(MAKEFLAGS) -f Makefile.nmake maintainer-clean
cd ../stats_tree
$(MAKE) /$(MAKEFLAGS) -f Makefile.nmake maintainer-clean
cd ../v5ua
@@ -353,6 +365,7 @@
xcopy rlm\*.dll $(VERSION) /d
xcopy rtnet\*.dll $(VERSION) /d
xcopy rudp\*.dll $(VERSION) /d
+ xcopy sbus\*.dll $(VERSION) /d
xcopy stats_tree\*.dll $(VERSION) /d
xcopy v5ua\*.dll $(VERSION) /d
!ENDIF
Index: /ethereal/plugins/Makefile.am
===================================================================
--- /ethereal/plugins/Makefile.am (revision 18189)
+++ /ethereal/plugins/Makefile.am (working copy)
@@ -52,6 +52,7 @@
rlm \
rtnet \
rudp \
+ sbus \
stats_tree \
v5ua
Index: /ethereal/plugins/sbus/packet-sbus.c
===================================================================
--- /ethereal/plugins/sbus/packet-sbus.c (revision 0)
+++ /ethereal/plugins/sbus/packet-sbus.c (revision 0)
@@ -0,0 +1,1687 @@
+/* packet-sbus.c
+ * Routines for Ether-S-Bus dissection
+ * Copyright 2006, Christian Durrer <christian.durrer@xxxxxxxxxxxx>
+ *
+ * $Id: README.developer 13926 2005-03-26 23:31:35Z guy $
+ *
+ * Ethereal - Network traffic analyzer
+ * By Gerald Combs <gerald@xxxxxxxxxxxx>
+ * Copyright 1998 Gerald Combs
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifdef HAVE_CONFIG_H
+#include "config.h"
+#endif
+
+#include <stdio.h>
+#include <stdlib.h>
+#include <string.h>
+#include <glib.h>
+#include <gmodule.h>
+#include <epan/packet.h>
+#include <epan/prefs.h>
+#include <epan/conversation.h>
+
+#ifndef ENABLE_STATIC
+G_MODULE_EXPORT const gchar version[] = "0.0.4";
+#endif
+
+/* Number of entries in the memeory chunk array (for conversation)*/
+#define SBUS_MEMCHUNKSIZE 20
+/* Attribut values*/
+#define SBUS_REQUEST 0x00
+#define SBUS_RESPONSE 0x01
+#define SBUS_ACKNAK 0x02
+
+/*SBus command codes*/
+#define SBUS_RD_COUNTER 0x00
+#define SBUS_RD_DISPLAY_REGISTER 0x01
+#define SBUS_RD_FLAG 0x02
+#define SBUS_RD_INPUT 0x03
+#define SBUS_RD_RTC 0x04
+#define SBUS_RD_OUTPUT 0x05
+#define SBUS_RD_REGISTER 0x06
+#define SBUS_RD_TIMER 0x07
+#define SBUS_WR_COUNTER 0x0A
+#define SBUS_WR_FLAG 0x0B
+#define SBUS_WR_RTC 0x0C
+#define SBUS_WR_OUTPUT 0x0D
+#define SBUS_WR_REGISTER 0x0E
+#define SBUS_WR_TIMER 0x0F
+#define SBUS_RDWR_MULTI_MEDIAS 0x13
+#define SBUS_RD_PCD_STATUS_CPU0 0x14
+#define SBUS_RD_PCD_STATUS_CPU1 0x15
+#define SBUS_RD_PCD_STATUS_CPU2 0x16
+#define SBUS_RD_PCD_STATUS_CPU3 0x17
+#define SBUS_RD_PCD_STATUS_CPU4 0x18
+#define SBUS_RD_PCD_STATUS_CPU5 0x19
+#define SBUS_RD_PCD_STATUS_CPU6 0x1A
+#define SBUS_RD_PCD_STATUS_OWN 0x1B
+#define SBUS_RD_SBUS_STN_NBR 0x1D
+#define SBUS_RD_USER_MEMORY 0x1E
+#define SBUS_RD_PROGRAM_LINE 0x1F
+#define SBUS_RD_PROGRAM_VERSION 0x20
+#define SBUS_RD_TEXT 0x21
+#define SBUS_RD_ACTIVE_TRANSITION 0x22
+#define SBUS_WR_USER_MEMORY 0x23
+#define SBUS_WR_PROGRAM_LINE 0x24
+#define SBUS_WR_TEXT 0x25
+#define SBUS_RUN_PROCEDURE_CPU0 0x28
+#define SBUS_RUN_PROCEDURE_CPU1 0x29
+#define SBUS_RUN_PROCEDURE_CPU2 0x2A
+#define SBUS_RUN_PROCEDURE_CPU3 0x2B
+#define SBUS_RUN_PROCEDURE_CPU4 0x2C
+#define SBUS_RUN_PROCEDURE_CPU5 0x2D
+#define SBUS_RUN_PROCEDURE_CPU6 0x2E
+#define SBUS_RUN_PROCEDURE_OWN 0x2F
+#define SBUS_RUN_PROCEDURE_ALL 0x30
+#define SBUS_RESTART_COLD_CPU1 0x32
+#define SBUS_RESTART_COLD_CPU2 0x33
+#define SBUS_RESTART_COLD_CPU3 0x34
+#define SBUS_RESTART_COLD_CPU4 0x35
+#define SBUS_RESTART_COLD_CPU5 0x36
+#define SBUS_RESTART_COLD_CPU6 0x37
+#define SBUS_RESTART_COLD_OWN 0x38
+#define SBUS_RESTART_COLD_ALL 0x39
+#define SBUS_STOP_PROCEDURE_CPU0 0x3C
+#define SBUS_STOP_PROCEDURE_CPU1 0x3D
+#define SBUS_STOP_PROCEDURE_CPU2 0x3E
+#define SBUS_STOP_PROCEDURE_CPU3 0x3F
+#define SBUS_STOP_PROCEDURE_CPU4 0x40
+#define SBUS_STOP_PROCEDURE_CPU5 0x41
+#define SBUS_STOP_PROCEDURE_CPU6 0x42
+#define SBUS_STOP_PROCEDURE_OWN 0x43
+#define SBUS_STOP_PROCEDURE_ALL 0x44
+#define SBUS_RD_STATUSFLAG_ACCU 0x46
+#define SBUS_RD_BYTE 0x47
+#define SBUS_RD_HALT_FAILURE_REG 0x48
+#define SBUS_RD_INDEX_REGISTER 0x49
+#define SBUS_RD_INSTRUCTION_POINTER 0x4A
+#define SBUS_FIND_HISTORY 0x4B
+#define SBUS_WR_STATUSFLAG_ACCU 0x50
+#define SBUS_WR_BYTE 0x51
+#define SBUS_WR_INDEX_REGISTER 0x52
+#define SBUS_WR_INSTRUCTION_POINTER 0x53
+#define SBUS_CLEAR_ALL 0x5A
+#define SBUS_CLEAR_FLAGS 0x5B
+#define SBUS_CLEAR_OUTPUTS 0x5C
+#define SBUS_CLEAR_REGISTERS 0x5D
+#define SBUS_CLEAR_TIMERS 0x5E
+#define SBUS_RESTART_WARM_CPU1 0x64
+#define SBUS_RESTART_WARM_CPU2 0x65
+#define SBUS_RESTART_WARM_CPU3 0x66
+#define SBUS_RESTART_WARM_CPU4 0x67
+#define SBUS_RESTART_WARM_CPU5 0x68
+#define SBUS_RESTART_WARM_CPU6 0x69
+#define SBUS_RESTART_WARM_OWN 0x6A
+#define SBUS_RESTART_WARM_ALL 0x6B
+#define SBUS_CHANGE_BLOCK 0x6E
+#define SBUS_CLEAR_HISTORY_FAILURE 0x6F
+#define SBUS_DELETE_PROGRAM_LINE 0x70
+#define SBUS_GO_CONDITIONAL 0x71
+#define SBUS_INSERT_PROGRAM_LINE 0x72
+#define SBUS_LOCAL_CYCLE 0x73
+#define SBUS_ALL_CYCLES 0x74
+#define SBUS_MAKE_TEXT 0x75
+#define SBUS_EXECUTE_SINGLE_INSTR 0x76
+#define SBUS_SINGLE_STEP 0x77
+#define SBUS_XOB_17_INTERRUPT 0x82
+#define SBUS_XOB_18_INTERRUPT 0x83
+#define SBUS_XOB_19_INTERRUPT 0x84
+#define SBUS_RD_HANGUP_TIMEOUT 0x91
+#define SBUS_RD_DATA_BLOCK 0x96
+#define SBUS_WR_DATA_BLOCK 0x97
+#define SBUS_MAKE_DATA_BLOCK 0x98
+#define SBUS_CLEAR_DATA_BLOCK 0x99
+#define SBUS_CLEAR_TEXT 0x9A
+#define SBUS_RD_BLOCK_ADDRESSES 0x9B
+#define SBUS_RD_BLOCK_SIZES 0x9C
+#define SBUS_RD_CURRENT_BLOCK 0x9D
+#define SBUS_RD_CALL_STACK 0x9E
+#define SBUS_RD_DBX 0x9F
+#define SBUS_RD_USER_EEPROM_REGISTER 0xA1
+#define SBUS_WR_USER_EEPROM_REGISTER 0xA3
+#define SBUS_ERASE_FLASH 0xA5
+#define SBUS_RESTART_COLD_FLAG 0xA6
+#define SBUS_WR_SYSTEM_BUFFER 0xA7
+#define SBUS_RD_SYSTEM_BUFFER 0xA8
+#define SBUS_RD_WR_PCD_BLOCK 0xA9
+#define SBUS_GET_DIAGNOSTIC 0xAA
+#define SBUS_RD_SYSTEM_INFORMATION 0xAB
+#define SBUS_CHANGE_BLOCKS_ON_RUN 0xAC
+#define SBUS_FLASHCARD_TELEGRAM 0xAD
+#define SBUS_DOWNLOAD_FIRMWARE 0xAE
+#define SBUS_WEB_SERVER_SERIAL_COMM 0xAF
+
+/* Bitfield in the arithmetic flags and accu*/
+#define F_ACCU (1<<0) /* Accumulator of PCD */
+#define F_ERROR (1<<1) /* Error flag of PCD */
+#define F_NEGATIVE (1<<2) /* Negative arithmetic status flag*/
+#define F_ZERO (1<<3) /* Zero arithmetic status flag */
+
+/* Bitfield in the system information*/
+/*#define F_EMPTY (1<<0) always 0 */
+#define F_MEMSIZE (1<<1) /* Memory size information*/
+#define F_TRACE (1<<2) /* Trace buffer feature */
+#define F_INFO_B1 (1<<3) /* EEPROM information of slot B1*/
+#define F_INFO_B2 (1<<4) /* EEPROM information of slot B2*/
+#define F_PGU_BAUD (1<<5) /* PGU baudrate can be switched*/
+
+/* Forward declaration we need below */
+void proto_reg_handoff_sbus(void);
+
+/* Initialize the protocol and registered fields */
+static int proto_sbus = -1;
+static int hf_sbus_length = -1;
+static int hf_sbus_version = -1;
+static int hf_sbus_protocol = -1;
+static int hf_sbus_sequence = -1;
+static int hf_sbus_attribut = -1;
+static int hf_sbus_dest = -1;
+static int hf_sbus_address = -1;
+static int hf_sbus_command = -1;
+static int hf_sbus_command_extension = -1;
+static int hf_sbus_rcount = -1;
+static int hf_sbus_wcount = -1;
+static int hf_sbus_wcount_calculated = -1;
+static int hf_sbus_fio_count = -1;
+static int hf_sbus_addr_rtc = -1;
+static int hf_sbus_addr_iof = -1;
+static int hf_sbus_addr_eeprom = -1;
+static int hf_sbus_addr_prog = -1;
+static int hf_sbus_addr_68k = -1;
+static int hf_sbus_block_type = -1;
+static int hf_sbus_block_nr = -1;
+static int hf_sbus_nbr_elements = -1;
+static int hf_sbus_display_register = -1;
+static int hf_sbus_data_rtc = -1;
+static int hf_sbus_data_byte = -1;
+static int hf_sbus_data_byte_hex = -1;
+static int hf_sbus_data_iof = -1;
+static int hf_sbus_cpu_type = -1;
+static int hf_sbus_fw_version = -1;
+static int hf_sbus_sysinfo_nr = -1;
+static int hf_sbus_sysinfo0_1 = -1;
+static int hf_sbus_sysinfo0_2 = -1;
+static int hf_sbus_sysinfo0_3 = -1;
+static int hf_sbus_sysinfo0_4 = -1;
+static int hf_sbus_sysinfo0_5 = -1;
+static int hf_sbus_sysinfo_length = -1;
+static int hf_sbus_f_module_type = -1;
+static int hf_sbus_harware_version = -1;
+static int hf_sbus_hardware_modification = -1;
+static int hf_sbus_various = -1;
+static int hf_sbus_acknackcode = -1;
+static int hf_sbus_cpu_status = -1;
+static int hf_sbus_week_day = -1;
+static int hf_sbus_date = -1;
+static int hf_sbus_time = -1;
+static int hf_sbus_crc = -1;
+static int hf_sbus_crc_bad = -1;
+static int hf_sbus_flags_accu = -1;
+static int hf_sbus_flags_error = -1;
+static int hf_sbus_flags_negative = -1;
+static int hf_sbus_flags_zero = -1;
+/* Web server telegram */
+static int hf_sbus_web_size = -1;
+static int hf_sbus_web_aid = -1;
+static int hf_sbus_web_seq = -1;
+
+/* Initialize the subtree pointers */
+static gint ett_sbus = -1;
+static gint ett_sbus_ether = -1;
+static gint ett_sbus_data = -1;
+
+/* True/False strings*/
+static const true_false_string tfs_sbus_flags= {
+ "Is high",
+ "Is low"
+};
+
+static const true_false_string tfs_sbus_present= {
+ "Is present",
+ "Is not present"
+};
+
+/* value to string definitions*/
+/* telegram types*/
+static const value_string sbus_att_vals[] = {
+ {0, "Request"},
+ {1, "Response"},
+ {2, "ACK/NAK"},
+ {0, NULL},
+};
+/* Block types*/
+static const value_string sbus_block_types[] = {
+ {0x00, "COB"},
+ {0x01, "XOB"},
+ {0x02, "PB"},
+ {0x03, "FB"},
+ {0x04, "ST"},
+ {0x05, "TR"},
+ {0x04, "TEXT"},
+ {0x05, "DB"},
+ {0x08, "SB"},
+ {0, NULL},
+};
+/* ACK NAK values*/
+static const value_string sbus_CPU_status[] = {
+ {0x43, "C"},
+ {0x44, "D"},
+ {0x48, "Halt"},
+ {0x52, "Run"},
+ {0x53, "Stop"},
+ {0x58, "X, Exceptional Intermediate Status (MODEMS+)"},
+ {0, NULL},
+};
+/* CPU status*/
+static const value_string sbus_ack_nak_vals[] = {
+ {0, "ACK (Acknowledged)"},
+ {1, "NAK, no reason specified"},
+ {2, "NAK, because of password"},
+ {3, "NAK, PGU port is in reduced protocol"},
+ {4, "NAK, PGU port is already used"},
+ {0, NULL},
+};
+/* S-Bus commands*/
+static const value_string sbus_command_vals[] = {
+ {0x00, "Read counter(s)"},
+ {0x01, "Read display register"},
+ {0x02, "Read flag(s)"},
+ {0x03, "Read input(s)"},
+ {0x04, "Read real time clock"},
+ {0x05, "Read output(s)"},
+ {0x06, "Read register(s)"},
+ {0x07, "Read timer(s)"},
+ {0x0A, "Write counter(s)"},
+ {0x0B, "Write flag(s)"},
+ {0x0C, "Write real time clock"},
+ {0x0D, "Write output(s)"},
+ {0x0E, "Write register(s)"},
+ {0x0F, "Write timer(s)"},
+ {0x14, "Read PCD status, CPU 0"},
+ {0x15, "Read PCD status, CPU 1"},
+ {0x16, "Read PCD status, CPU 2"},
+ {0x17, "Read PCD status, CPU 3"},
+ {0x18, "Read PCD status, CPU 4"},
+ {0x19, "Read PCD status, CPU 5"},
+ {0x1A, "Read PCD status, CPU 6"},
+ {0x1B, "Read PCD status (own)"},
+ {0x1D, "Read S-Bus station number"},
+ {0x1E, "Read user memory*"},
+ {0x1F, "Read program line*"},
+ {0x20, "Read firmware version"},
+ {0x21, "Read text*"},
+ {0x22, "Read active transition*"},
+ {0x23, "Write user memeory*"},
+ {0x24, "Write program line*"},
+ {0x25, "Write text*"},
+ {0x28, "Run procedure*, CPU 0"},
+ {0x29, "Run procedure*, CPU 1"},
+ {0x2A, "Run procedure*, CPU 2"},
+ {0x2B, "Run procedure*, CPU 3"},
+ {0x2C, "Run procedure*, CPU 4"},
+ {0x2D, "Run procedure*, CPU 5"},
+ {0x2E, "Run procedure*, CPU 6"},
+ {0x2F, "Run procedure* (own CPU)"},
+ {0x30, "Run procedure* (All CPUs)"},
+ {0x32, "Restart cold CPU 1*"},
+ {0x33, "Restart cold CPU 2*"},
+ {0x34, "Restart cold CPU 3*"},
+ {0x35, "Restart cold CPU 4*"},
+ {0x36, "Restart cold CPU 5*"},
+ {0x37, "Restart cold CPU 6*"},
+ {0x38, "Restart cold own CPU*"},
+ {0x39, "Restart cold all CPUs*"},
+ {0x3C, "Stop procedure*, CPU 0"},
+ {0x3D, "Stop procedure*, CPU 1"},
+ {0x3E, "Stop procedure*, CPU 2"},
+ {0x3F, "Stop procedure*, CPU 3"},
+ {0x40, "Stop procedure*, CPU 4"},
+ {0x41, "Stop procedure*, CPU 5"},
+ {0x42, "Stop procedure*, CPU 6"},
+ {0x43, "Stop procedure*, (own CPU)"},
+ {0x44, "Stop procedure*, (All CPUs)"},
+ {0x46, "Read arithmetic status and ACCU*"},
+ {0x47, "Read byte"},
+ {0x48, "Read halt failure register*"},
+ {0x49, "Read index register*"},
+ {0x4A, "Read instruction pointer*"},
+ {0x4B, "Find history*"},
+ {0x50, "Write arithmetic staus and ACCU*"},
+ {0x51, "Write byte*"},
+ {0x52, "Write index register"},
+ {0x53, "Write instruction pointer*"},
+ {0x5A, "Clear all (F, O, R, T)*"},
+ {0x5B, "Clear flags*"},
+ {0x5C, "Clear outputs*"},
+ {0x5D, "Clear registers*"},
+ {0x5E, "Clear timers*"},
+ {0x64, "Restart warm CPU 1*"},
+ {0x65, "Restart warm CPU 2*"},
+ {0x66, "Restart warm CPU 3*"},
+ {0x67, "Restart warm CPU 4*"},
+ {0x68, "Restart warm CPU 5*"},
+ {0x69, "Restart warm CPU 6*"},
+ {0x6A, "Restart warm (own CPU)*"},
+ {0x6B, "Restart warm (All CPUs)*"},
+ {0x6E, "Change block*"},
+ {0x6F, "Clear history failure*"},
+ {0x70, "Delete program line*"},
+ {0x71, "Go conditional*"},
+ {0x72, "Insert program line*"},
+ {0x73, "Local cycles*"},
+ {0x74, "All cycles*"},
+ {0x75, "Make text*"},
+ {0x76, "Execute single instruction*"},
+ {0x77, "Single step*"},
+ {0x82, "XOB 17 interrupt"},
+ {0x83, "XOB 18 interrupt"},
+ {0x84, "XOB 19 interrupt"},
+ {0x91, "Read hangup timeout"},
+ {0x96, "Read data block"},
+ {0x97, "Write data block"},
+ {0x98, "Make data block*"},
+ {0x99, "Clear data block*"},
+ {0x9A, "Clear text*"},
+ {0x9B, "Read block address"},
+ {0x9C, "Read block sizes"},
+ {0x9D, "Read current block*"},
+ {0x9E, "Read call stack*"},
+ {0x9F, "Read DBX"},
+ {0xA1, "Read user EEPROM register"},
+ {0xA3, "Write user EEPROM register"},
+ {0xA5, "Erase flash*"},
+ {0xA6, "Restart cold flag*"},
+ {0xA7, "Write system buffer"},
+ {0xA8, "Read system buffer"},
+ {0xAA, "Get diagnostic*"},
+ {0xAB, "Read system information*"},
+ {0xAC, "Changes blocks on run*"},
+ {0xAD, "Flashcard telegram*"},
+ {0xAE, "Download FW*"},
+ {0xAF, "Web server serial communication*"},
+ {0, NULL},
+};
+
+static const value_string webserver_aid_vals[] = {
+ {0x01, "Partitial request"},
+ {0x02, "Request end"},
+ {0x07, "Get Data"},
+ {0x10, "Transfer OK"},
+ {0x11, "Partial answer"},
+ {0x12, "Last part of answer"},
+ {0x13, "Server not ready"},
+ {0, NULL}
+};
+
+static const guint crc_table[] = {
+ 0x0000,0x1021,0x2042,0x3063,0x4084,0x50a5,0x60c6,0x70e7,0x8108,0x9129,0xa14a,0xb16b,0xc18c,0xd1ad,0xe1ce,0xf1ef,
+ 0x1231,0x0210,0x3273,0x2252,0x52b5,0x4294,0x72f7,0x62d6,0x9339,0x8318,0xb37b,0xa35a,0xd3bd,0xc39c,0xf3ff,0xe3de,
+ 0x2462,0x3443,0x0420,0x1401,0x64e6,0x74c7,0x44a4,0x5485,0xa56a,0xb54b,0x8528,0x9509,0xe5ee,0xf5cf,0xc5ac,0xd58d,
+ 0x3653,0x2672,0x1611,0x0630,0x76d7,0x66f6,0x5695,0x46b4,0xb75b,0xa77a,0x9719,0x8738,0xf7df,0xe7fe,0xd79d,0xc7bc,
+ 0x48c4,0x58e5,0x6886,0x78a7,0x0840,0x1861,0x2802,0x3823,0xc9cc,0xd9ed,0xe98e,0xf9af,0x8948,0x9969,0xa90a,0xb92b,
+ 0x5af5,0x4ad4,0x7ab7,0x6a96,0x1a71,0x0a50,0x3a33,0x2a12,0xdbfd,0xcbdc,0xfbbf,0xeb9e,0x9b79,0x8b58,0xbb3b,0xab1a,
+ 0x6ca6,0x7c87,0x4ce4,0x5cc5,0x2c22,0x3c03,0x0c60,0x1c41,0xedae,0xfd8f,0xcdec,0xddcd,0xad2a,0xbd0b,0x8d68,0x9d49,
+ 0x7e97,0x6eb6,0x5ed5,0x4ef4,0x3e13,0x2e32,0x1e51,0x0e70,0xff9f,0xefbe,0xdfdd,0xcffc,0xbf1b,0xaf3a,0x9f59,0x8f78,
+ 0x9188,0x81a9,0xb1ca,0xa1eb,0xd10c,0xc12d,0xf14e,0xe16f,0x1080,0x00a1,0x30c2,0x20e3,0x5004,0x4025,0x7046,0x6067,
+ 0x83b9,0x9398,0xa3fb,0xb3da,0xc33d,0xd31c,0xe37f,0xf35e,0x02b1,0x1290,0x22f3,0x32d2,0x4235,0x5214,0x6277,0x7256,
+ 0xb5ea,0xa5cb,0x95a8,0x8589,0xf56e,0xe54f,0xd52c,0xc50d,0x34e2,0x24c3,0x14a0,0x0481,0x7466,0x6447,0x5424,0x4405,
+ 0xa7db,0xb7fa,0x8799,0x97b8,0xe75f,0xf77e,0xc71d,0xd73c,0x26d3,0x36f2,0x0691,0x16b0,0x6657,0x7676,0x4615,0x5634,
+ 0xd94c,0xc96d,0xf90e,0xe92f,0x99c8,0x89e9,0xb98a,0xa9ab,0x5844,0x4865,0x7806,0x6827,0x18c0,0x08e1,0x3882,0x28a3,
+ 0xcb7d,0xdb5c,0xeb3f,0xfb1e,0x8bf9,0x9bd8,0xabbb,0xbb9a,0x4a75,0x5a54,0x6a37,0x7a16,0x0af1,0x1ad0,0x2ab3,0x3a92,
+ 0xfd2e,0xed0f,0xdd6c,0xcd4d,0xbdaa,0xad8b,0x9de8,0x8dc9,0x7c26,0x6c07,0x5c64,0x4c45,0x3ca2,0x2c83,0x1ce0,0x0cc1,
+ 0xef1f,0xff3e,0xcf5d,0xdf7c,0xaf9b,0xbfba,0x8fd9,0x9ff8,0x6e17,0x7e36,0x4e55,0x5e74,0x2e93,0x3eb2,0x0ed1,0x1ef0
+};
+
+/* Conversion values passing structure*/
+typedef struct {
+ guint32 conversation; /*Conversation ID*/
+ guint16 sequence; /*Sequence number of request telegram*/
+} sbus_request_key;
+
+typedef struct {
+ guint8 cmd_code; /*command code from request*/
+ guint8 count; /*rcount value*/
+ guint8 sysinfo; /*system information number (or command in other telegrams)*/
+} sbus_request_val;
+
+/* The GMemChunk base structure (for conversations)*/
+static GHashTable *sbus_request_hash = NULL;
+static GMemChunk *sbus_request_keys = NULL;
+static GMemChunk *sbus_request_vals = NULL;
+
+static guint crc_calc (guint crc, guint val)
+{
+ int index;
+ guint ncrc;
+
+ index = (((crc >> 8) ^ val) & 0xff);
+ ncrc = crc_table[index] ^ ((crc << 8) & 0xffff);
+
+ return ncrc;
+}
+
+/* Hash functions*/
+static gint sbus_equal(gconstpointer v, gconstpointer w)
+{
+ sbus_request_key *v1 = (sbus_request_key *)v;
+ sbus_request_key *v2 = (sbus_request_key *)w;
+
+ if (v1->conversation == v2->conversation &&
+ v1->sequence == v2->sequence) {
+ return 1;
+ }
+ return 0;
+}
+
+static guint sbus_hash(gconstpointer v)
+{
+ sbus_request_key *key = (sbus_request_key *)v;
+ guint val;
+ val = key->conversation + key->sequence;
+ return val;
+}
+
+/*Protocol initialisation*/
+static void sbus_init_protocol(void){
+ if (sbus_request_hash){
+ g_hash_table_destroy(sbus_request_hash);
+ }
+ if (sbus_request_keys){
+ g_mem_chunk_destroy(sbus_request_keys);
+ }
+ if (sbus_request_vals){
+ g_mem_chunk_destroy(sbus_request_vals);
+ }
+ sbus_request_hash = g_hash_table_new(sbus_hash, sbus_equal);
+ sbus_request_keys = g_mem_chunk_new("sbus_request_keys",
+ sizeof(sbus_request_key),
+ SBUS_MEMCHUNKSIZE * sizeof(sbus_request_key),
+ G_ALLOC_AND_FREE);
+ sbus_request_vals = g_mem_chunk_new("sbus_request_vals",
+ sizeof(sbus_request_val),
+ SBUS_MEMCHUNKSIZE * sizeof(sbus_request_val),
+ G_ALLOC_AND_FREE);
+}
+
+/*Dissect the telegram*/
+static void
+dissect_sbus(tvbuff_t *tvb, packet_info *pinfo, proto_tree *tree)
+{
+
+/* Set up structures needed to add the protocol subtree and manage it */
+ proto_item *ti, *et, *dt;
+ proto_tree *sbus_tree, *ethsbus_tree, *sbusdata_tree;
+
+ gboolean interpreted; /*for indication of interpreted telegrams*/
+ gint i; /*for CRC calculation*/
+ gint j; /*for CRC calculation*/
+ gint offset;
+ gint sbus_eth_len;
+ guint sbus_crc_calc;
+ guint8 sbus_version;
+ guint8 sbus_attribut;
+ guint8 sbus_media_cnt;
+ guint8 sbus_fio_cnt;
+ guint8 sbus_cmd_code;
+ /*guint8 sbus_hash_cmd_code;*/
+ guint8 sbus_web_size;
+ guint8 sbus_web_aid;
+ guint8 sbus_web_seq;
+ guint8 sbus_sysinfo_number;
+ /*guint8 sbus_sysinfolenght;*/
+ guint32 sbus_binarymasked;
+ guint32 sbus_binaries;
+ guint16 sbus_ack_code;
+ /* guint32 sbus_length;*/
+ /* guint32 sbus_sequence;*/
+ guint32 sbus_show_bin;
+ guint32 sbus_helper;
+ guint32 sbus_helper1;
+ guint32 sbus_helper2;
+ char *tmp_string;
+
+/* Set up conversations*/
+ conversation_t *conversation = NULL;
+ sbus_request_key request_key, *new_request_key;
+ sbus_request_val *request_val = NULL;
+
+ conversation = find_conversation(pinfo->fd->num, &pinfo->src, &pinfo->dst,
+ pinfo->ptype, pinfo->srcport, pinfo->destport, 0);
+
+ if (!conversation){
+ /* create new conversation*/
+ conversation = conversation_new(pinfo->fd->num, &pinfo->src, &pinfo->dst,
+ pinfo->ptype, pinfo->srcport, pinfo->destport, 0);
+ }
+
+ request_key.conversation = conversation->index;
+ request_key.sequence = tvb_get_ntohs(tvb,6);
+
+ request_val = (sbus_request_val *) g_hash_table_lookup(sbus_request_hash,
+ &request_key);
+ /* Only allocate a new hash element when it's a request*/
+ sbus_attribut = tvb_get_guint8(tvb,8);
+
+ if ( !request_val && sbus_attribut == 0 ) {/* request telegram */
+
+ new_request_key = g_mem_chunk_alloc(sbus_request_keys);
+ *new_request_key = request_key;
+
+ request_val = g_mem_chunk_alloc(sbus_request_vals);
+ request_val->cmd_code=tvb_get_guint8(tvb,10);
+
+ if (((request_val->cmd_code) == 0xA1) ||
+ ((request_val->cmd_code) == 0xA3)){
+ request_val->count=((tvb_get_guint8(tvb,12))+1);
+ }
+ else {request_val->count=((tvb_get_guint8(tvb,11))+1);}
+
+ /*Enter system info*/
+ if ((request_val->cmd_code) == 0xAB){
+ request_val->sysinfo=(tvb_get_guint8(tvb,12));
+ }
+ else {request_val->sysinfo=0x0;}
+
+ g_hash_table_insert(sbus_request_hash, new_request_key, request_val);
+ }
+/* End of attaching data to hash table*/
+
+/* Make entries in Protocol column and Info column on summary display */
+ if (check_col(pinfo->cinfo, COL_PROTOCOL))
+ col_set_str(pinfo->cinfo, COL_PROTOCOL, "S-Bus");
+
+ if (check_col(pinfo->cinfo, COL_INFO))
+ col_clear(pinfo->cinfo, COL_INFO);
+ offset = 0 ;
+
+ if (check_col(pinfo->cinfo, COL_INFO)) {
+
+
+/* sbus_ack_code = tvb_get_ntohs(tvb,10);*/
+ switch (sbus_attribut){
+ case SBUS_REQUEST:
+ sbus_cmd_code = tvb_get_guint8(tvb,10);
+
+ /* Special treatment of web server request
+ * as is is very helpful to see more information in the packetlist */
+ if (sbus_cmd_code == 0xAF) {
+ sbus_web_aid = tvb_get_guint8(tvb,12);
+ sbus_web_seq = tvb_get_guint8(tvb, 13);
+
+ col_add_fstr(pinfo->cinfo, COL_INFO,
+ "Web Server Request: %s (Seq No: %d)",
+ val_to_str(sbus_web_aid,
+ webserver_aid_vals, "Unknown Request!"),
+ sbus_web_seq);
+ } else {
+ /* All other requests */
+ col_add_fstr(pinfo->cinfo, COL_INFO,
+ "Request: %s", val_to_str(sbus_cmd_code,
+ sbus_command_vals, "Unknown Command!"));
+ }
+ break;
+
+ case SBUS_RESPONSE:
+ /* Special treatment of web server request
+ * as is is very helpful to see more information in the packetlist */
+ if (request_val && ((request_val->cmd_code) == SBUS_WEB_SERVER_SERIAL_COMM)) {
+ sbus_web_aid = tvb_get_guint8(tvb,10);
+ col_add_fstr(pinfo->cinfo, COL_INFO,
+ "Response: %s (Seq No: %d)",
+ val_to_str(sbus_web_aid,
+ webserver_aid_vals, "Unknown Request!"),
+ sbus_web_seq);
+
+ } else {
+ col_set_str(pinfo->cinfo, COL_INFO, "Response");
+ }
+ break;
+
+ case SBUS_ACKNAK:
+ sbus_ack_code = tvb_get_ntohs(tvb,9);
+ col_add_fstr(pinfo->cinfo, COL_INFO,
+ "%s", val_to_str(sbus_ack_code,
+ sbus_ack_nak_vals,
+ "Unknown NAK response code!"));
+ break;
+
+ default:
+ break;
+ }
+
+ }
+/* create display subtree for the protocol */
+ if (tree) {
+
+ ti = proto_tree_add_item(tree, proto_sbus, tvb, 0, -1, FALSE);
+
+ sbus_tree = proto_item_add_subtree(ti, ett_sbus);
+
+/*Add subtree for Ether-S-Bus header*/
+ et = proto_tree_add_text(sbus_tree, tvb, 0, 8, "Ether-S-Bus header");
+ ethsbus_tree = proto_item_add_subtree(et, ett_sbus_ether);
+ sbus_version = tvb_get_guint8(tvb,0x4);
+
+/* add an item to the subtree*/
+ sbus_eth_len = tvb_get_ntohl(tvb,offset);
+ proto_tree_add_item(ethsbus_tree,
+ hf_sbus_length, tvb, offset, 4, FALSE);
+ offset += 4;
+
+ proto_tree_add_item(ethsbus_tree,
+ hf_sbus_version, tvb, offset, 1, FALSE);
+ offset += 1;
+
+ proto_tree_add_item(ethsbus_tree,
+ hf_sbus_protocol, tvb, offset, 1, FALSE);
+ offset += 1;
+
+ proto_tree_add_item(ethsbus_tree,
+ hf_sbus_sequence, tvb, offset, 2, FALSE);
+ offset += 2;
+
+/* Continue adding stuff to the main tree*/
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_attribut, tvb, offset, 1, FALSE);
+ offset += 1;
+
+ sbus_attribut = tvb_get_guint8(tvb,8);
+ if (sbus_attribut == SBUS_REQUEST){
+ interpreted = FALSE;
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_dest, tvb, offset, 1, FALSE);
+ offset += 1;
+ sbus_cmd_code = tvb_get_guint8(tvb,10);
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_command, tvb, offset, 1, FALSE);
+ offset += 1;
+
+ /*Read Counter, Register or Timer*/
+ if ((sbus_cmd_code == SBUS_RD_COUNTER) ||
+ (sbus_cmd_code == SBUS_RD_REGISTER) ||
+ (sbus_cmd_code == SBUS_RD_TIMER)){
+ sbus_media_cnt = (tvb_get_guint8(tvb,11))+1;
+ proto_tree_add_uint(sbus_tree,
+ hf_sbus_rcount, tvb, offset, 1, sbus_media_cnt);
+ offset += 1;
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_addr_rtc, tvb, offset, 2, FALSE);
+ offset += 2;
+ interpreted = TRUE;
+ }
+ /*Read Flag, Input or Output*/
+ if ((sbus_cmd_code == SBUS_RD_FLAG) ||
+ (sbus_cmd_code == SBUS_RD_INPUT) ||
+ (sbus_cmd_code == SBUS_RD_OUTPUT)){
+ sbus_media_cnt = (tvb_get_guint8(tvb,11))+1;
+ proto_tree_add_uint(sbus_tree,
+ hf_sbus_rcount, tvb, offset, 1, sbus_media_cnt);
+ offset += 1;
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_addr_iof, tvb, offset, 2, FALSE);
+ offset += 2;
+ interpreted = TRUE;
+ }
+ /*Write Register Timer Counter*/
+ if ((sbus_cmd_code == SBUS_WR_COUNTER) ||
+ (sbus_cmd_code == SBUS_WR_REGISTER) ||
+ (sbus_cmd_code == SBUS_WR_TIMER)){
+ sbus_media_cnt = (tvb_get_guint8(tvb,11));
+ sbus_media_cnt = ((sbus_media_cnt - 1)/4);
+ proto_tree_add_uint(sbus_tree,
+ hf_sbus_wcount_calculated, tvb, offset,
+ 1, sbus_media_cnt);
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_wcount, tvb, offset, 1, FALSE);
+ offset += 1;
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_addr_rtc, tvb, offset, 2, FALSE);
+ offset += 2;
+ /*Add subtree for Data*/
+ dt = proto_tree_add_text(sbus_tree, tvb, offset,
+ ((sbus_media_cnt) * 4),"Data");
+
+ sbusdata_tree = proto_item_add_subtree(dt, ett_sbus_data);
+ for (i=((sbus_media_cnt)); i>0; i--){
+ proto_tree_add_item(sbusdata_tree,
+ hf_sbus_data_rtc, tvb, offset,
+ 4, FALSE);
+ offset += 4;
+
+ }
+ interpreted = TRUE;
+ }
+ /* Write flags and outputs*/
+ if ((sbus_cmd_code == SBUS_WR_FLAG) ||
+ (sbus_cmd_code == SBUS_WR_OUTPUT)){
+ sbus_media_cnt = (tvb_get_guint8(tvb,11));
+ sbus_media_cnt = ((sbus_media_cnt - 2 ));
+ sbus_fio_cnt = (tvb_get_guint8(tvb,14));
+ sbus_fio_cnt = ((sbus_fio_cnt + 1 ));
+ proto_tree_add_uint(sbus_tree,
+ hf_sbus_wcount_calculated, tvb, offset,
+ 1, sbus_media_cnt);
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_wcount, tvb, offset, 1, FALSE);
+ offset += 1;
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_addr_iof, tvb, offset, 2, FALSE);
+ offset += 2;
+ proto_tree_add_uint(sbus_tree,
+ hf_sbus_fio_count, tvb, offset, 1, sbus_fio_cnt);
+ offset += 1;
+ /*Add subtree for Data*/
+ dt = proto_tree_add_text(sbus_tree, tvb, offset,
+ (sbus_media_cnt),"Data");
+
+ sbusdata_tree = proto_item_add_subtree(dt, ett_sbus_data);
+ for (i= sbus_media_cnt; i>0; i--){
+
+ sbus_helper = 1;
+ sbus_show_bin = 0;
+ sbus_binarymasked = 0x01;
+ sbus_binaries = tvb_get_guint8(tvb, offset);
+ for (j=0; j<8; j++){
+ if ((sbus_binarymasked & sbus_binaries) != 0) {
+ sbus_show_bin = (sbus_show_bin + sbus_helper);
+ }
+ sbus_binarymasked = sbus_binarymasked<<1;
+ sbus_helper = 10 * sbus_helper;
+ }
+
+ proto_tree_add_uint_format(sbusdata_tree,
+ hf_sbus_data_iof, tvb, offset, 1, sbus_show_bin,
+ "Binary data: %08u", sbus_show_bin);
+ offset += 1;
+
+ }
+ interpreted = TRUE;
+ }
+ /* Request: Write Real time clock*/
+ if (sbus_cmd_code == SBUS_WR_RTC){
+ sbus_helper = tvb_get_guint8(tvb, (offset +5)); /*hours*/
+ sbus_helper1 = tvb_get_guint8(tvb, (offset +6)); /*minutes*/
+ sbus_helper2 = tvb_get_guint8(tvb, (offset +7)); /*seconds*/
+ proto_tree_add_text(sbus_tree, tvb, (offset +5), 3,
+ "Time (HH:MM:SS): %02x:%02x:%02x", sbus_helper, sbus_helper1, sbus_helper2);
+ sbus_helper = tvb_get_guint8(tvb, (offset +2)); /*year*/
+ sbus_helper1 = tvb_get_guint8(tvb, (offset +3)); /*month*/
+ sbus_helper2 = tvb_get_guint8(tvb, (offset +4)); /*day*/
+ proto_tree_add_text(sbus_tree, tvb, (offset +2), 3,
+ "Date (YY/MM/DD): %02x/%02x/%02x", sbus_helper, sbus_helper1, sbus_helper2);
+ sbus_helper = tvb_get_guint8(tvb, (offset)); /*year-week*/
+ sbus_helper1 = tvb_get_guint8(tvb, (offset +1)); /*week-day*/
+ proto_tree_add_text(sbus_tree, tvb, offset, 2,
+ "Calendar week: %x, Week day: %x", sbus_helper, sbus_helper1);
+ /*Add subtree for Data*/
+ dt = proto_tree_add_text(sbus_tree, tvb, offset,
+ 8, "Clock data");
+ sbusdata_tree = proto_item_add_subtree(dt, ett_sbus_data);
+
+ proto_tree_add_item(sbusdata_tree,
+ hf_sbus_week_day, tvb, offset, 2, FALSE);
+ offset += 2;
+ proto_tree_add_item(sbusdata_tree,
+ hf_sbus_date, tvb, offset, 3, FALSE);
+ offset += 3;
+ proto_tree_add_item(sbusdata_tree,
+ hf_sbus_time, tvb, offset, 3, FALSE);
+ offset += 3;
+ interpreted = TRUE;
+ }
+
+
+ /* Read user memory or program line*/
+ if ((sbus_cmd_code == SBUS_RD_USER_MEMORY) ||
+ (sbus_cmd_code == SBUS_RD_PROGRAM_LINE)){
+ sbus_media_cnt = (tvb_get_guint8(tvb,11))+1;
+ proto_tree_add_uint(sbus_tree,
+ hf_sbus_rcount, tvb, offset, 1, sbus_media_cnt);
+ offset += 1;
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_addr_prog, tvb, offset, 3, FALSE);
+ offset += 3;
+ interpreted = TRUE;
+ }
+
+ /*Write user memory*/
+ if (sbus_cmd_code == SBUS_WR_USER_MEMORY){
+ sbus_media_cnt = (tvb_get_guint8(tvb,11));
+ sbus_media_cnt = ((sbus_media_cnt - 2)/4);
+ proto_tree_add_uint(sbus_tree,
+ hf_sbus_wcount_calculated, tvb, offset,
+ 1, sbus_media_cnt);
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_wcount, tvb, offset, 1, FALSE);
+ offset += 1;
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_addr_68k, tvb, offset, 3, FALSE);
+ offset += 3;
+ /*Add subtree for Data*/
+ dt = proto_tree_add_text(sbus_tree, tvb, offset,
+ ((sbus_media_cnt) * 4),"Program lines");
+
+ sbusdata_tree = proto_item_add_subtree(dt, ett_sbus_data);
+ for (i=((sbus_media_cnt)); i>0; i--){
+ proto_tree_add_item(sbusdata_tree,
+ hf_sbus_data_rtc, tvb, offset,
+ 4, FALSE);
+ offset += 4;
+
+ }
+ interpreted = TRUE;
+ }
+
+ /* Read byte*/
+ if (sbus_cmd_code == SBUS_RD_BYTE){
+ sbus_media_cnt = (tvb_get_guint8(tvb,11))+1;
+ proto_tree_add_uint(sbus_tree,
+ hf_sbus_rcount, tvb, offset, 1, sbus_media_cnt);
+ offset += 1;
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_addr_68k, tvb, offset, 3, FALSE);
+ offset += 3;
+ interpreted = TRUE;
+ }
+
+ /* Write byte */
+ if (sbus_cmd_code == SBUS_WR_BYTE){
+ sbus_media_cnt = (tvb_get_guint8(tvb,11));
+ sbus_media_cnt = ((sbus_media_cnt - 2));
+ proto_tree_add_uint(sbus_tree,
+ hf_sbus_wcount_calculated, tvb, offset,
+ 1, sbus_media_cnt);
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_wcount, tvb, offset, 1, FALSE);
+ offset += 1;
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_addr_68k, tvb, offset, 3, FALSE);
+ offset += 3;
+ /*Add subtree for Data*/
+ dt = proto_tree_add_text(sbus_tree, tvb, offset,
+ ((sbus_media_cnt) * 4),"Data (bytes)");
+
+ sbusdata_tree = proto_item_add_subtree(dt, ett_sbus_data);
+ for (i=((sbus_media_cnt)); i>0; i--){
+ proto_tree_add_item(sbusdata_tree,
+ hf_sbus_data_byte, tvb, offset,
+ 1, FALSE);
+ offset += 1;
+ }
+ interpreted = TRUE;
+ }
+
+ /*Read EEPROM register*/
+ if (sbus_cmd_code == SBUS_RD_USER_EEPROM_REGISTER){
+ sbus_media_cnt = (tvb_get_guint8(tvb,12))+1;
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_command_extension, tvb, offset, 1, FALSE);
+ offset += 1;
+ proto_tree_add_uint(sbus_tree,
+ hf_sbus_rcount, tvb, offset, 1, sbus_media_cnt);
+ offset += 1;
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_addr_eeprom, tvb, offset, 2, FALSE);
+ offset += 2;
+ interpreted = TRUE;
+ }
+
+ /*Request for reading system info
+ Syinfo 05 is not implemented as no serial baud is possible*/
+ if (sbus_cmd_code == SBUS_RD_SYSTEM_INFORMATION){
+ sbus_sysinfo_number = (tvb_get_guint8(tvb,13));
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_sysinfo_nr, tvb, offset, 1, FALSE);
+ offset += 1;
+ sbus_sysinfo_number = (tvb_get_guint8(tvb,14));
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_sysinfo_nr, tvb, offset, 1, FALSE);
+ offset += 1;
+ interpreted = TRUE;
+ }
+
+ /* WebServer Request */
+ if (sbus_cmd_code == SBUS_WEB_SERVER_SERIAL_COMM) {
+ sbus_web_size = tvb_get_guint8(tvb,11);
+ sbus_web_aid = tvb_get_guint8(tvb,12);
+ sbus_web_seq = tvb_get_guint8(tvb,13);
+
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_web_size, tvb, offset,
+ 1, sbus_web_size);
+ offset += 1;
+
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_web_aid, tvb, offset,
+ 1, sbus_web_aid);
+ offset += 1;
+
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_web_seq, tvb, offset,
+ 1, sbus_web_seq);
+ offset += 1;
+
+ if (sbus_web_size > 1) {
+ dt = proto_tree_add_text(sbus_tree, tvb, offset,
+ (sbus_web_size - 1),"Data (bytes)");
+
+ sbusdata_tree = proto_item_add_subtree(dt, ett_sbus_data);
+ for (i=sbus_web_size -1 ; i>0; i--){
+ proto_tree_add_item(sbusdata_tree,
+ hf_sbus_data_byte, tvb, offset,
+ 1, FALSE);
+ offset += 1;
+ }
+ }
+ interpreted = TRUE;
+ }
+
+/*Inform that command was not dissected and add remaining length*/
+ if ((interpreted == FALSE) && (sbus_eth_len > 13)){ /*13 bytes is the minimal length of a request telegram...*/
+ sbus_helper = sbus_eth_len - (offset + 2);
+ proto_tree_add_text(sbus_tree, tvb, offset, sbus_helper,
+ "This telegram isn't implemented in the dissector.");
+ offset = offset + sbus_helper;
+ }
+ }
+
+/* Response dissection*/
+ if (request_val && sbus_attribut == SBUS_RESPONSE) {
+ interpreted = FALSE;
+ /* Response: 32 bit values*/
+ if (((request_val->cmd_code) == SBUS_RD_COUNTER) || /*32 bit vals (R,T,C)*/
+ ((request_val->cmd_code) == SBUS_RD_REGISTER) ||
+ ((request_val->cmd_code) == SBUS_RD_TIMER) ||
+ ((request_val->cmd_code) == SBUS_RD_USER_MEMORY) || /* User Memory */
+ ((request_val->cmd_code) == SBUS_RD_PROGRAM_LINE) || /* Program line */
+ ((request_val->cmd_code) == SBUS_RD_USER_EEPROM_REGISTER)){ /* EEPROM reg*/
+
+ /*Add subtree for Data*/
+ dt = proto_tree_add_text(sbus_tree, tvb, offset,
+ ((request_val->count) * 4),"Data");
+/*printf("Debug5\n");*/
+ sbusdata_tree = proto_item_add_subtree(dt, ett_sbus_data);
+/*printf("Debug6\n");*/
+ for (i=(request_val->count); i>0; i--){
+
+ proto_tree_add_item(sbusdata_tree,
+ hf_sbus_data_rtc, tvb, offset,
+ 4, FALSE);
+ offset += 4;
+ }
+ interpreted = TRUE;
+ }
+ /* Response: PCD Display register*/
+ if ((request_val->cmd_code) == SBUS_RD_DISPLAY_REGISTER){
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_display_register, tvb, offset, 4, FALSE);
+ offset += 4;
+ interpreted = TRUE;
+ }
+ /* Add binary data I, O, F*/
+ if (((request_val->cmd_code) == SBUS_RD_FLAG) ||
+ ((request_val->cmd_code) == SBUS_RD_INPUT) ||
+ ((request_val->cmd_code) == SBUS_RD_OUTPUT)){
+
+ /*Add subtree for Data*/
+ dt = proto_tree_add_text(sbus_tree, tvb, offset,
+ (((request_val->count) + 7) / 8), "Data");
+ sbusdata_tree = proto_item_add_subtree(dt, ett_sbus_data);
+
+ for (i=(((request_val->count) + 7) / 8); i>0; i--){
+
+ sbus_helper = 1;
+ sbus_show_bin = 0;
+ sbus_binarymasked = 0x01;
+ sbus_binaries = tvb_get_guint8(tvb, offset);
+ for (j=0; j<8; j++){
+ if ((sbus_binarymasked & sbus_binaries) != 0) {
+ sbus_show_bin = (sbus_show_bin + sbus_helper);
+ }
+ sbus_binarymasked = sbus_binarymasked<<1;
+ sbus_helper = 10 * sbus_helper;
+ }
+
+ proto_tree_add_uint_format(sbusdata_tree,
+ hf_sbus_data_iof, tvb, offset, 1, sbus_show_bin,
+ "Binary data: %08u", sbus_show_bin);
+ offset += 1;
+ }
+ interpreted = TRUE;
+ }
+
+ /* Response: Real time clock value*/
+ if ((request_val->cmd_code) == SBUS_RD_RTC){
+ sbus_helper = tvb_get_guint8(tvb, (offset +5)); /*hours*/
+ sbus_helper1 = tvb_get_guint8(tvb, (offset +6)); /*minutes*/
+ sbus_helper2 = tvb_get_guint8(tvb, (offset +7)); /*seconds*/
+ proto_tree_add_text(sbus_tree, tvb, (offset +5), 3,
+ "Time (HH:MM:SS): %02x:%02x:%02x", sbus_helper, sbus_helper1, sbus_helper2);
+ sbus_helper = tvb_get_guint8(tvb, (offset +2)); /*year*/
+ sbus_helper1 = tvb_get_guint8(tvb, (offset +3)); /*month*/
+ sbus_helper2 = tvb_get_guint8(tvb, (offset +4)); /*day*/
+ proto_tree_add_text(sbus_tree, tvb, (offset +2), 3,
+ "Date (YY/MM/DD): %02x/%02x/%02x", sbus_helper, sbus_helper1, sbus_helper2);
+ sbus_helper = tvb_get_guint8(tvb, (offset)); /*year-week*/
+ sbus_helper1 = tvb_get_guint8(tvb, (offset +1)); /*week-day*/
+ proto_tree_add_text(sbus_tree, tvb, offset, 2,
+ "Calendar week: %x, Week day: %x", sbus_helper, sbus_helper1);
+ /*Add subtree for Data*/
+ dt = proto_tree_add_text(sbus_tree, tvb, offset,
+ 8, "Clock data");
+ sbusdata_tree = proto_item_add_subtree(dt, ett_sbus_data);
+
+ proto_tree_add_item(sbusdata_tree,
+ hf_sbus_week_day, tvb, offset, 2, FALSE);
+ offset += 2;
+ proto_tree_add_item(sbusdata_tree,
+ hf_sbus_date, tvb, offset, 3, FALSE);
+ offset += 3;
+ proto_tree_add_item(sbusdata_tree,
+ hf_sbus_time, tvb, offset, 3, FALSE);
+ offset += 3;
+ interpreted = TRUE;
+ }
+
+ /* Response: CPU status, the command codes 14..1B are concerned*/
+ if (((request_val->cmd_code) > 0x13) &&
+ ((request_val->cmd_code) < 0x1C)){
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_cpu_status, tvb, offset, 1, FALSE);
+ offset += 1;
+ interpreted = TRUE;
+ }
+
+ /* Response: Station address*/
+ if (((request_val->cmd_code) == SBUS_RD_SBUS_STN_NBR)){
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_address, tvb, offset, 1, FALSE);
+ offset += 1;
+ interpreted = TRUE;
+ }
+
+ /* Response: Firmware version */
+ if (((request_val->cmd_code) == SBUS_RD_PROGRAM_VERSION)){
+ /*PCD type*/
+ tmp_string = tvb_get_string(tvb, offset, 5);
+ proto_tree_add_string(sbus_tree,
+ hf_sbus_cpu_type, tvb, offset, 5, tmp_string);
+ offset += 5;
+ g_free(tmp_string);
+ /*FW version*/
+ tmp_string = tvb_get_string(tvb , offset, 3);
+ proto_tree_add_string(sbus_tree,
+ hf_sbus_fw_version, tvb, offset, 3, tmp_string);
+ offset += 4;
+ g_free(tmp_string);
+ interpreted = TRUE;
+ }
+
+ /* Response for Status Flags*/
+ if ((request_val->cmd_code) == SBUS_RD_STATUSFLAG_ACCU){
+
+ /*Add subtree for Data*/
+ dt = proto_tree_add_text(sbus_tree, tvb, offset,
+ 1,"ACCU and arithmetic status");
+ sbusdata_tree = proto_item_add_subtree(dt, ett_sbus_data);
+
+ proto_tree_add_item(sbusdata_tree, hf_sbus_flags_accu,
+ tvb, offset, 1, FALSE);
+ proto_tree_add_item(sbusdata_tree, hf_sbus_flags_error,
+ tvb, offset, 1, FALSE);
+ proto_tree_add_item(sbusdata_tree, hf_sbus_flags_negative,
+ tvb, offset, 1, FALSE);
+ proto_tree_add_item(sbusdata_tree, hf_sbus_flags_zero,
+ tvb, offset, 1, FALSE);
+ offset +=1;
+ interpreted = TRUE;
+ }
+
+ /* Response for Read byte */
+ if ((request_val->cmd_code) == SBUS_RD_BYTE){
+
+ /*Add subtree for Data*/
+ dt = proto_tree_add_text(sbus_tree, tvb, offset,
+ (request_val->count),"Data (bytes)");
+
+ sbusdata_tree = proto_item_add_subtree(dt, ett_sbus_data);
+ for (i=(request_val->count); i>0; i--){
+ proto_tree_add_item(sbusdata_tree,
+ hf_sbus_data_byte, tvb, offset,
+ 1, FALSE);
+ offset += 1;
+ }
+ interpreted = TRUE;
+ }
+
+ /* Response for Read Index register */
+ if ((request_val->cmd_code) == SBUS_RD_INDEX_REGISTER){
+
+ /*Add subtree for Data*/
+ dt = proto_tree_add_text(sbus_tree, tvb, offset,
+ 2,"Data (hex bytes)");
+
+ sbusdata_tree = proto_item_add_subtree(dt, ett_sbus_data);
+ for (i=0; i<2; i++){ /*2 bytes*/
+ proto_tree_add_item(sbusdata_tree,
+ hf_sbus_data_byte_hex, tvb, offset,
+ 1, FALSE);
+ offset += 1;
+ }
+ interpreted = TRUE;
+ }
+
+ /* Response: Instruction pointer*/
+ if (((request_val->cmd_code) == SBUS_RD_INSTRUCTION_POINTER)){
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_addr_prog, tvb, offset, 3, FALSE);
+ offset += 3;
+ interpreted = TRUE;
+ }
+
+ /*Response for Find History*/
+ if (((request_val->cmd_code) == SBUS_FIND_HISTORY)){
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_addr_68k, tvb, offset, 3, FALSE);
+ offset += 3;
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_nbr_elements, tvb, offset, 2, FALSE);
+ offset += 2;
+ interpreted = TRUE;
+ }
+
+ /* Response: Read current block*/
+ if (((request_val->cmd_code) == SBUS_RD_CURRENT_BLOCK)){
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_block_type, tvb, offset, 1, FALSE);
+ offset += 1;
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_block_nr, tvb, offset, 2, FALSE);
+ offset += 2;
+ interpreted = TRUE;
+ }
+
+ /* Response: Read system infomation (without interpretation of module info)*/
+ if (((request_val->cmd_code) == SBUS_RD_SYSTEM_INFORMATION)){
+ if (((request_val->sysinfo) == 0x00)){ /*sysinfo 0*/
+ offset +=1; /* this byte is always 0x01*/
+ /*Add subtree for Data*/
+ dt = proto_tree_add_text(sbus_tree, tvb, offset,
+ 1,"System info");
+ sbusdata_tree = proto_item_add_subtree(dt, ett_sbus_data);
+
+ proto_tree_add_item(sbusdata_tree, hf_sbus_sysinfo0_1,
+ tvb, offset, 1, FALSE);
+ proto_tree_add_item(sbusdata_tree, hf_sbus_sysinfo0_2,
+ tvb, offset, 1, FALSE);
+ proto_tree_add_item(sbusdata_tree, hf_sbus_sysinfo0_3,
+ tvb, offset, 1, FALSE);
+ proto_tree_add_item(sbusdata_tree, hf_sbus_sysinfo0_4,
+ tvb, offset, 1, FALSE);
+ proto_tree_add_item(sbusdata_tree, hf_sbus_sysinfo0_5,
+ tvb, offset, 1, FALSE);
+ offset +=1;
+ interpreted = TRUE;
+ }
+ }
+
+ /* Response: Webserver request */
+ if (((request_val->cmd_code) == SBUS_WEB_SERVER_SERIAL_COMM)) {
+ sbus_web_size = tvb_get_guint8(tvb, 9);
+ sbus_web_aid = tvb_get_guint8(tvb,10);
+ sbus_web_seq = tvb_get_guint8(tvb,11);
+
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_web_size, tvb, offset,
+ 1, sbus_web_size);
+ offset += 1;
+
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_web_aid, tvb, offset,
+ 1, sbus_web_aid);
+ offset += 1;
+
+ if (sbus_web_size > 1) {
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_web_seq, tvb, offset,
+ 1, sbus_web_seq);
+ offset += 1;
+
+ dt = proto_tree_add_text(sbus_tree, tvb, offset,
+ (sbus_web_size - 2),"Data (bytes)");
+
+ sbusdata_tree = proto_item_add_subtree(dt, ett_sbus_data);
+ for (i=sbus_web_size - 2 ; i>0; i--){
+ proto_tree_add_item(sbusdata_tree,
+ hf_sbus_data_byte, tvb, offset,
+ 1, FALSE);
+ offset += 1;
+ }
+ }
+ interpreted = TRUE;
+ }
+
+ /*Inform that response was not dissected and add remaining length*/
+ if (interpreted == FALSE){
+ sbus_helper = sbus_eth_len - (offset + 2);
+ proto_tree_add_text(sbus_tree, tvb, offset, sbus_helper,
+ "This telegram isn't implemented in the dissector.");
+ offset = offset + sbus_helper;
+ }
+ }
+
+ if (sbus_attribut == SBUS_ACKNAK){
+ proto_tree_add_item(sbus_tree,
+ hf_sbus_acknackcode, tvb, offset, 2, FALSE);
+ offset += 2;
+ }
+
+ /* Calclulate CRC */
+ sbus_crc_calc = 0;
+ for (i = 0; i < sbus_eth_len - 2; i++)
+ sbus_crc_calc = crc_calc (sbus_crc_calc, tvb_get_guint8(tvb, i));
+ /*Show CRC and add hidden item for wrong CRC*/
+ sbus_helper = tvb_get_ntohs(tvb, offset);
+ if (sbus_helper == sbus_crc_calc){
+ proto_tree_add_uint_format(sbus_tree,
+ hf_sbus_crc, tvb, offset, 2, sbus_helper,
+ "Checksum: 0x%04x (correct)", sbus_helper);
+ }
+ else {
+ proto_tree_add_uint_format(sbus_tree,
+ hf_sbus_crc, tvb, offset, 2, sbus_helper,
+ "Checksum: 0x%04x (NOT correct)", sbus_helper);
+ proto_tree_add_boolean_hidden(sbus_tree,
+ hf_sbus_crc_bad, tvb, offset + 2, 2, TRUE);
+ }
+ offset += 2; /*now at the end of the telegram*/
+ }
+/*End of dissect_sbus*/
+}
+
+/* Register the protocol with Ethereal */
+
+void
+proto_register_sbus(void)
+{
+
+/* Setup list of header fields See Section 1.6.1 for details*/
+ static hf_register_info hf[] = {
+ { &hf_sbus_length,
+ { "Length (bytes)", "sbus.len",
+ FT_UINT32, BASE_DEC, NULL, 0,
+ "SAIA Ether-S-Bus telegram length", HFILL }
+ },
+ { &hf_sbus_version,
+ { "Version", "sbus.vers",
+ FT_UINT8, BASE_DEC, NULL, 0,
+ "SAIA Ether-S-Bus version", HFILL }
+ },
+ { &hf_sbus_protocol,
+ { "Protocol type", "sbus.proto",
+ FT_UINT8, BASE_DEC, NULL, 0,
+ "SAIA Ether-S-Bus protocol type", HFILL }
+ },
+ { &hf_sbus_sequence,
+ { "Sequence", "sbus.seq",
+ FT_UINT16, BASE_DEC, NULL, 0,
+ "SAIA Ether-S-Bus sequence number", HFILL }
+ },
+
+ { &hf_sbus_attribut,
+ { "Telegram attribute", "sbus.att",
+ FT_UINT8, BASE_HEX, VALS(sbus_att_vals), 0,
+ "SAIA Ether-S-Bus telegram attribute, indicating type of telegram", HFILL }
+ },
+
+ { &hf_sbus_dest,
+ { "Destination", "sbus.destination",
+ FT_UINT8, BASE_DEC, NULL, 0,
+ "SAIA S-Bus destination address", HFILL }
+ },
+
+ { &hf_sbus_address,
+ { "S-Bus address", "sbus.address",
+ FT_UINT8, BASE_DEC, NULL, 0,
+ "SAIA S-Bus station address", HFILL }
+ },
+
+ { &hf_sbus_command,
+ { "Command", "sbus.cmd",
+ FT_UINT8, BASE_HEX, VALS(sbus_command_vals), 0,
+ "SAIA S-Bus command", HFILL }
+ },
+
+ { &hf_sbus_command_extension,
+ { "Command extension", "sbus.cmd_extn",
+ FT_UINT8, BASE_HEX, NULL, 0,
+ "SAIA S-Bus command extension", HFILL }
+ },
+
+ { &hf_sbus_rcount,
+ { "R-count", "sbus.rcount",
+ FT_UINT8, BASE_DEC, NULL, 0,
+ "Number of elements expected in response", HFILL }
+ },
+
+ { &hf_sbus_wcount,
+ { "W-count (raw)", "sbus.wcount",
+ FT_UINT8, BASE_DEC, NULL, 0,
+ "Number of bytes to be written", HFILL }
+ },
+
+ { &hf_sbus_wcount_calculated,
+ { "W-count (32 bit values)", "sbus.wcount_calc",
+ FT_UINT8, BASE_DEC, NULL, 0,
+ "Number of elements to be written", HFILL }
+ },
+
+ { &hf_sbus_fio_count,
+ { "FIO Count (amount of bits)", "sbus.fio_count",
+ FT_UINT8, BASE_DEC, NULL, 0,
+ "Number of binary elements to be written", HFILL }
+ },
+
+
+ { &hf_sbus_addr_rtc,
+ { "Base address RTC", "sbus.addr_RTC",
+ FT_UINT16, BASE_DEC, NULL, 0,
+ "Base address of 32 bit elements to read", HFILL }
+ },
+
+ { &hf_sbus_addr_iof,
+ { "Base address IOF", "sbus.addr_IOF",
+ FT_UINT16, BASE_DEC, NULL, 0,
+ "Base address of binary elements to read", HFILL }
+ },
+
+ { &hf_sbus_addr_eeprom,
+ { "Base address of EEPROM register", "sbus.addr_EEPROM",
+ FT_UINT16, BASE_DEC, NULL, 0,
+ "Base address of 32 bit EEPROM register to read or write", HFILL }
+ },
+
+ { &hf_sbus_addr_prog,
+ { "Base address of user memory or program lines", "sbus.addr_prog",
+ FT_UINT24, BASE_DEC, NULL, 0,
+ "Base address of the user memory or program lines (read or write)", HFILL }
+ },
+
+ { &hf_sbus_addr_68k,
+ { "Base address of bytes", "sbus.addr_prog",
+ FT_UINT24, BASE_HEX, NULL, 0,
+ "Base address of bytes to read or write (68k address)", HFILL }
+ },
+
+ { &hf_sbus_block_type,
+ { "Block type", "sbus.block_type",
+ FT_UINT8, BASE_HEX, VALS(sbus_block_types), 0,
+ "Program block type read", HFILL }
+ },
+
+ { &hf_sbus_block_nr,
+ { "Block/Element nr", "sbus.block_nr",
+ FT_UINT16, BASE_DEC, NULL, 0,
+ "Program block / DatatBlock number", HFILL }
+ },
+
+ { &hf_sbus_nbr_elements,
+ { "Number of elements", "sbus.nbr_elements",
+ FT_UINT16, BASE_DEC, NULL, 0,
+ "Number of elements or characters", HFILL }
+ },
+
+
+ { &hf_sbus_display_register,
+ { "PCD Display register", "sbus.data_display_register",
+ FT_UINT32, BASE_DEC, NULL, 0,
+ "The PCD display register (32 bit value)", HFILL }
+ },
+
+ { &hf_sbus_data_rtc,
+ { "S-Bus 32-bit data", "sbus.data_rtc",
+ FT_UINT32, BASE_DEC, NULL, 0,
+ "One regiser/timer of counter (32 bit value)", HFILL }
+ },
+
+ { &hf_sbus_data_byte,
+ { "Data bytes", "sbus.data_byte",
+ FT_UINT8, BASE_DEC, NULL, 0,
+ "One byte from PCD", HFILL }
+ },
+
+ { &hf_sbus_data_byte_hex,
+ { "Data bytes (hex)", "sbus.data_byte_hex",
+ FT_UINT8, BASE_HEX, NULL, 0,
+ "One byte from PCD (hexadecimal)", HFILL }
+ },
+
+ { &hf_sbus_data_iof,
+ { "S-Bus binary data", "sbus.data_iof",
+ FT_UINT32, BASE_DEC, NULL, 0,
+ "8 binaries", HFILL }
+ },
+
+ { &hf_sbus_cpu_type,
+ { "PCD type", "sbus.pcd_type",
+ FT_STRING, BASE_NONE, NULL, 0,
+ "PCD type (short form)", HFILL }
+ },
+
+ { &hf_sbus_fw_version,
+ { "Firmware version", "sbus.fw_version",
+ FT_STRING, BASE_NONE, NULL, 0,
+ "Firmware version of the PCD or module", HFILL }
+ },
+
+ { &hf_sbus_sysinfo_nr,
+ { "System information number", "sbus.sysinfo",
+ FT_UINT8, BASE_HEX, NULL, 0,
+ "System information number (extension to command code)", HFILL }
+ },
+
+ { &hf_sbus_sysinfo0_1,
+ { "Mem size info", "sbus.sysinfo0.mem",
+ FT_BOOLEAN, 8, TFS(&tfs_sbus_present), F_MEMSIZE,
+ "Availability of memory size information", HFILL }
+ },
+ { &hf_sbus_sysinfo0_2,
+ { "Trace buffer", "sbus.sysinfo0.trace",
+ FT_BOOLEAN, 8, TFS(&tfs_sbus_present), F_TRACE,
+ "Availability of trace buffer feature", HFILL }
+ },
+ { &hf_sbus_sysinfo0_3,
+ { "Slot B1", "sbus.sysinfo0.b1",
+ FT_BOOLEAN, 8, TFS(&tfs_sbus_present), F_INFO_B1,
+ "Presence of EEPROM information on slot B1", HFILL }
+ },
+ { &hf_sbus_sysinfo0_4,
+ { "Slot B2", "sbus.sysinfo0.b2",
+ FT_BOOLEAN, 8, TFS(&tfs_sbus_present), F_INFO_B2,
+ "Presence of EEPROM information on slot B2", HFILL }
+ },
+ { &hf_sbus_sysinfo0_5,
+ { "PGU baud", "sbus.sysinfo0.pgubaud",
+ FT_BOOLEAN, 8, TFS(&tfs_sbus_present), F_PGU_BAUD,
+ "Availability of PGU baud switch feature", HFILL }
+ },
+
+ { &hf_sbus_sysinfo_length,
+ { "System information length", "sbus.sysinfo_length",
+ FT_UINT8, BASE_HEX, NULL, 0,
+ "System information length in response", HFILL }
+ },
+
+ { &hf_sbus_f_module_type,
+ { "F-module type", "sbus.fmodule_type",
+ FT_STRING, BASE_NONE, NULL, 0,
+ "Module type mounted on B1/2 slot", HFILL }
+ },
+
+ { &hf_sbus_harware_version,
+ { "Hardware version", "sbus.hw_version",
+ FT_STRING, BASE_NONE, NULL, 0,
+ "Hardware version of the PCD or the module", HFILL }
+ },
+
+ { &hf_sbus_hardware_modification,
+ { "Hardware modification", "sbus.hw_modification",
+ FT_UINT8, BASE_DEC, NULL, 0,
+ "Hardware modification of the PCD or module", HFILL }
+ },
+
+ { &hf_sbus_various,
+ { "Varous data", "sbus.various",
+ FT_NONE, BASE_NONE, NULL, 0,
+ "Various data contained in telegrams but nobody will search for it", HFILL }
+ },
+
+
+ { &hf_sbus_acknackcode,
+ { "ACK/NAK code", "sbus.nakcode",
+ FT_UINT16, BASE_HEX, VALS(sbus_ack_nak_vals), 0,
+ "SAIA S-Bus ACK/NAK response", HFILL }
+ },
+
+ { &hf_sbus_cpu_status,
+ { "CPU status", "sbus.CPU_status",
+ FT_UINT8, BASE_HEX, VALS(sbus_CPU_status), 0,
+ "SAIA PCD CPU status", HFILL }
+ },
+
+
+ { &hf_sbus_week_day,
+ { "RTC calendar week and week day", "sbus.rtc.week_day",
+ FT_UINT16, BASE_HEX, NULL, 0,
+ "Calendar week and week day number of the real time clock", HFILL }
+ },
+
+ { &hf_sbus_date,
+ { "RTC date (YYMMDD)", "sbus.rtc.date",
+ FT_UINT24, BASE_HEX, NULL, 0,
+ "Year, month and day of the real time clock", HFILL }
+ },
+
+ { &hf_sbus_time,
+ { "RTC time (HHMMSS)", "sbus.rtc.time",
+ FT_UINT24, BASE_HEX, NULL, 0,
+ "Time of the real time clock", HFILL }
+ },
+
+ { &hf_sbus_web_size,
+ { "Web server packet size", "sbus.web.size",
+ FT_UINT8, BASE_HEX, NULL, 0,
+ "Web server packet size", HFILL }
+ },
+
+ { &hf_sbus_web_aid,
+ { "AID", "sbus.web.aid",
+ FT_UINT8, BASE_HEX, NULL, 0,
+ "Web server command/status code (AID)", HFILL }
+ },
+
+ { &hf_sbus_web_seq,
+ { "Sequence", "sbus.web.seq",
+ FT_UINT8, BASE_HEX, NULL, 0,
+ "Web server sequence nr (PACK_N)", HFILL }
+ },
+
+ { &hf_sbus_crc,
+ { "Checksum", "sbus.crc",
+ FT_UINT16, BASE_HEX, NULL, 0,
+ "CRC 16", HFILL }
+ },
+
+ { &hf_sbus_crc_bad,
+ { "Bad Checksum", "sbus.crc_bad", FT_BOOLEAN, BASE_NONE, NULL, 0x0,
+ "A bad checksum in the telegram", HFILL }},
+
+ { &hf_sbus_flags_accu,
+ { "ACCU", "sbus.flags.accu",
+ FT_BOOLEAN, 8, TFS(&tfs_sbus_flags), F_ACCU,
+ "PCD Accumulator", HFILL }
+ },
+
+ { &hf_sbus_flags_error,
+ { "Error flag", "sbus.flags.error",
+ FT_BOOLEAN, 8, TFS(&tfs_sbus_flags), F_ERROR,
+ "PCD error flag", HFILL }
+ },
+
+ { &hf_sbus_flags_negative,
+ { "N-flag", "sbus.flags.nflag",
+ FT_BOOLEAN, 8, TFS(&tfs_sbus_flags), F_NEGATIVE,
+ "Negative status flag", HFILL }
+ },
+
+ { &hf_sbus_flags_zero,
+ { "Z-flag", "sbus.flags.zflag",
+ FT_BOOLEAN, 8, TFS(&tfs_sbus_flags), F_ZERO,
+ "Zero status flag", HFILL }
+ },
+ };
+
+/* Setup protocol subtree array */
+ static gint *ett[] = {
+ &ett_sbus,
+ &ett_sbus_ether,
+ &ett_sbus_data,
+ };
+
+/* Register the protocol name and description */
+ proto_sbus = proto_register_protocol("SAIA S-Bus",
+ "SBUS", "sbus");
+
+/* Required function calls to register the header fields and subtrees used */
+ proto_register_field_array(proto_sbus, hf, array_length(hf));
+ proto_register_subtree_array(ett, array_length(ett));
+ register_init_routine(&sbus_init_protocol);
+}
+
+void
+proto_reg_handoff_sbus(void)
+{
+ dissector_handle_t sbus_handle;
+
+ sbus_handle = create_dissector_handle(dissect_sbus,
+ proto_sbus);
+ dissector_add("udp.port", 5050, sbus_handle);
+}
+
+/* Stuff to register the dissector when it's used as a dll or shared library */
+#ifndef ENABLE_STATIC
+G_MODULE_EXPORT void
+plugin_register(void)
+{
+ static int inited = 0;
+
+ /* register the sbus protocol, protocol fields, and subtrees */
+ if (proto_sbus == -1 ) { /*was !inited before CD051017*/
+ /* execute protocol initialization only once */
+ proto_register_sbus();
+ inited = 1;
+ }
+}
+
+G_MODULE_EXPORT void
+plugin_reg_handoff(void)
+{
+ proto_reg_handoff_sbus();
+}
+#endif
Index: /ethereal/plugins/sbus/Makefile.common
===================================================================
--- /ethereal/plugins/sbus/Makefile.common (revision 0)
+++ /ethereal/plugins/sbus/Makefile.common (revision 0)
@@ -0,0 +1,33 @@
+# Makefile.common for Ether-S-Bus plugin
+# Contains the stuff from Makefile.am and Makefile.nmake that is
+# a) common to both files and
+# b) portable between both files
+#
+# $Id: Makefile.common 17961 2006-04-22 20:26:16Z guy $
+#
+# Ethereal - Network traffic analyzer
+# By Gerald Combs <gerald@xxxxxxxxxxxx>
+# Copyright 1998 Gerald Combs
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License
+# as published by the Free Software Foundation; either version 2
+# of the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+
+# the name of the plugin
+PLUGIN_NAME = sbus
+
+# the dissector sources (without any helpers)
+DISSECTOR_SRC = \
+ packet-sbus.c
+
+# corresponding headers
Index: /ethereal/plugins/sbus/authors
===================================================================
--- /ethereal/plugins/sbus/authors (revision 0)
+++ /ethereal/plugins/sbus/authors (revision 0)
@@ -0,0 +1,3 @@
+Author :
+Christian Durrer <christian.durrer@xxxxxxxxxxxx>
+
Index: /ethereal/plugins/sbus/ChangeLog
===================================================================
--- /ethereal/plugins/sbus/ChangeLog (revision 0)
+++ /ethereal/plugins/sbus/ChangeLog (revision 0)
@@ -0,0 +1,2 @@
+$Id: ChangeLog 11400 2004-07-18 00:24:25Z guy $
+
Index: /ethereal/plugins/sbus/Makefile.nmake
===================================================================
--- /ethereal/plugins/sbus/Makefile.nmake (revision 0)
+++ /ethereal/plugins/sbus/Makefile.nmake (revision 0)
@@ -0,0 +1,31 @@
+#
+# $Id: Makefile.nmake 13596 2005-03-05 06:28:10Z lroland $
+#
+
+include ..\..\config.nmake
+
+############### no need to modify below this line #########
+
+CFLAGS=/DHAVE_CONFIG_H /I../.. /I../../wiretap $(GLIB_CFLAGS) \
+ /I$(PCAP_DIR)\include -D_U_="" $(LOCAL_CFLAGS)
+
+LDFLAGS = /NOLOGO /INCREMENTAL:no /MACHINE:I386 $(LOCAL_LDFLAGS)
+
+!IFDEF ENABLE_LIBETHEREAL
+LINK_PLUGIN_WITH=..\..\epan\libethereal.lib
+CFLAGS=/DHAVE_WIN32_LIBETHEREAL_LIB /D_NEED_VAR_IMPORT_ $(CFLAGS)
+
+OBJECTS=packet-sbus.obj
+
+sbus.dll sbus.exp sbus.lib : $(OBJECTS) $(LINK_PLUGIN_WITH)
+ link -dll /out:sbus.dll $(LDFLAGS) $(OBJECTS) $(LINK_PLUGIN_WITH) \
+ $(GLIB_LIBS)
+
+!ENDIF
+
+clean:
+ rm -f $(OBJECTS) sbus.dll sbus.exp sbus.lib *.pdb
+
+distclean: clean
+
+maintainer-clean: distclean
Index: /ethereal/plugins/sbus/moduleinfo.h
===================================================================
--- /ethereal/plugins/sbus/moduleinfo.h (revision 0)
+++ /ethereal/plugins/sbus/moduleinfo.h (revision 0)
@@ -0,0 +1,17 @@
+/* Included *after* config.h, in order to re-define these macros */
+
+#ifdef PACKAGE
+#undef PACKAGE
+#endif
+
+/* Name of package */
+#define PACKAGE "sbus"
+
+
+#ifdef VERSION
+#undef VERSION
+#endif
+
+/* Version number of package */
+#define VERSION "0.0.4"
+
Index: /ethereal/plugins/sbus/copying
===================================================================
--- /ethereal/plugins/sbus/copying (revision 0)
+++ /ethereal/plugins/sbus/copying (revision 0)
@@ -0,0 +1,340 @@
+ GNU GENERAL PUBLIC LICENSE
+ Version 2, June 1991
+
+ Copyright (C) 1989, 1991 Free Software Foundation, Inc.
+ 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ Everyone is permitted to copy and distribute verbatim copies
+ of this license document, but changing it is not allowed.
+
+ Preamble
+
+ The licenses for most software are designed to take away your
+freedom to share and change it. By contrast, the GNU General Public
+License is intended to guarantee your freedom to share and change free
+software--to make sure the software is free for all its users. This
+General Public License applies to most of the Free Software
+Foundation's software and to any other program whose authors commit to
+using it. (Some other Free Software Foundation software is covered by
+the GNU Library General Public License instead.) You can apply it to
+your programs, too.
+
+ When we speak of free software, we are referring to freedom, not
+price. Our General Public Licenses are designed to make sure that you
+have the freedom to distribute copies of free software (and charge for
+this service if you wish), that you receive source code or can get it
+if you want it, that you can change the software or use pieces of it
+in new free programs; and that you know you can do these things.
+
+ To protect your rights, we need to make restrictions that forbid
+anyone to deny you these rights or to ask you to surrender the rights.
+These restrictions translate to certain responsibilities for you if you
+distribute copies of the software, or if you modify it.
+
+ For example, if you distribute copies of such a program, whether
+gratis or for a fee, you must give the recipients all the rights that
+you have. You must make sure that they, too, receive or can get the
+source code. And you must show them these terms so they know their
+rights.
+
+ We protect your rights with two steps: (1) copyright the software, and
+(2) offer you this license which gives you legal permission to copy,
+distribute and/or modify the software.
+
+ Also, for each author's protection and ours, we want to make certain
+that everyone understands that there is no warranty for this free
+software. If the software is modified by someone else and passed on, we
+want its recipients to know that what they have is not the original, so
+that any problems introduced by others will not reflect on the original
+authors' reputations.
+
+ Finally, any free program is threatened constantly by software
+patents. We wish to avoid the danger that redistributors of a free
+program will individually obtain patent licenses, in effect making the
+program proprietary. To prevent this, we have made it clear that any
+patent must be licensed for everyone's free use or not licensed at all.
+
+ The precise terms and conditions for copying, distribution and
+modification follow.
+
+ GNU GENERAL PUBLIC LICENSE
+ TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
+
+ 0. This License applies to any program or other work which contains
+a notice placed by the copyright holder saying it may be distributed
+under the terms of this General Public License. The "Program", below,
+refers to any such program or work, and a "work based on the Program"
+means either the Program or any derivative work under copyright law:
+that is to say, a work containing the Program or a portion of it,
+either verbatim or with modifications and/or translated into another
+language. (Hereinafter, translation is included without limitation in
+the term "modification".) Each licensee is addressed as "you".
+
+Activities other than copying, distribution and modification are not
+covered by this License; they are outside its scope. The act of
+running the Program is not restricted, and the output from the Program
+is covered only if its contents constitute a work based on the
+Program (independent of having been made by running the Program).
+Whether that is true depends on what the Program does.
+
+ 1. You may copy and distribute verbatim copies of the Program's
+source code as you receive it, in any medium, provided that you
+conspicuously and appropriately publish on each copy an appropriate
+copyright notice and disclaimer of warranty; keep intact all the
+notices that refer to this License and to the absence of any warranty;
+and give any other recipients of the Program a copy of this License
+along with the Program.
+
+You may charge a fee for the physical act of transferring a copy, and
+you may at your option offer warranty protection in exchange for a fee.
+
+ 2. You may modify your copy or copies of the Program or any portion
+of it, thus forming a work based on the Program, and copy and
+distribute such modifications or work under the terms of Section 1
+above, provided that you also meet all of these conditions:
+
+ a) You must cause the modified files to carry prominent notices
+ stating that you changed the files and the date of any change.
+
+ b) You must cause any work that you distribute or publish, that in
+ whole or in part contains or is derived from the Program or any
+ part thereof, to be licensed as a whole at no charge to all third
+ parties under the terms of this License.
+
+ c) If the modified program normally reads commands interactively
+ when run, you must cause it, when started running for such
+ interactive use in the most ordinary way, to print or display an
+ announcement including an appropriate copyright notice and a
+ notice that there is no warranty (or else, saying that you provide
+ a warranty) and that users may redistribute the program under
+ these conditions, and telling the user how to view a copy of this
+ License. (Exception: if the Program itself is interactive but
+ does not normally print such an announcement, your work based on
+ the Program is not required to print an announcement.)
+
+These requirements apply to the modified work as a whole. If
+identifiable sections of that work are not derived from the Program,
+and can be reasonably considered independent and separate works in
+themselves, then this License, and its terms, do not apply to those
+sections when you distribute them as separate works. But when you
+distribute the same sections as part of a whole which is a work based
+on the Program, the distribution of the whole must be on the terms of
+this License, whose permissions for other licensees extend to the
+entire whole, and thus to each and every part regardless of who wrote it.
+
+Thus, it is not the intent of this section to claim rights or contest
+your rights to work written entirely by you; rather, the intent is to
+exercise the right to control the distribution of derivative or
+collective works based on the Program.
+
+In addition, mere aggregation of another work not based on the Program
+with the Program (or with a work based on the Program) on a volume of
+a storage or distribution medium does not bring the other work under
+the scope of this License.
+
+ 3. You may copy and distribute the Program (or a work based on it,
+under Section 2) in object code or executable form under the terms of
+Sections 1 and 2 above provided that you also do one of the following:
+
+ a) Accompany it with the complete corresponding machine-readable
+ source code, which must be distributed under the terms of Sections
+ 1 and 2 above on a medium customarily used for software interchange; or,
+
+ b) Accompany it with a written offer, valid for at least three
+ years, to give any third party, for a charge no more than your
+ cost of physically performing source distribution, a complete
+ machine-readable copy of the corresponding source code, to be
+ distributed under the terms of Sections 1 and 2 above on a medium
+ customarily used for software interchange; or,
+
+ c) Accompany it with the information you received as to the offer
+ to distribute corresponding source code. (This alternative is
+ allowed only for noncommercial distribution and only if you
+ received the program in object code or executable form with such
+ an offer, in accord with Subsection b above.)
+
+The source code for a work means the preferred form of the work for
+making modifications to it. For an executable work, complete source
+code means all the source code for all modules it contains, plus any
+associated interface definition files, plus the scripts used to
+control compilation and installation of the executable. However, as a
+special exception, the source code distributed need not include
+anything that is normally distributed (in either source or binary
+form) with the major components (compiler, kernel, and so on) of the
+operating system on which the executable runs, unless that component
+itself accompanies the executable.
+
+If distribution of executable or object code is made by offering
+access to copy from a designated place, then offering equivalent
+access to copy the source code from the same place counts as
+distribution of the source code, even though third parties are not
+compelled to copy the source along with the object code.
+
+ 4. You may not copy, modify, sublicense, or distribute the Program
+except as expressly provided under this License. Any attempt
+otherwise to copy, modify, sublicense or distribute the Program is
+void, and will automatically terminate your rights under this License.
+However, parties who have received copies, or rights, from you under
+this License will not have their licenses terminated so long as such
+parties remain in full compliance.
+
+ 5. You are not required to accept this License, since you have not
+signed it. However, nothing else grants you permission to modify or
+distribute the Program or its derivative works. These actions are
+prohibited by law if you do not accept this License. Therefore, by
+modifying or distributing the Program (or any work based on the
+Program), you indicate your acceptance of this License to do so, and
+all its terms and conditions for copying, distributing or modifying
+the Program or works based on it.
+
+ 6. Each time you redistribute the Program (or any work based on the
+Program), the recipient automatically receives a license from the
+original licensor to copy, distribute or modify the Program subject to
+these terms and conditions. You may not impose any further
+restrictions on the recipients' exercise of the rights granted herein.
+You are not responsible for enforcing compliance by third parties to
+this License.
+
+ 7. If, as a consequence of a court judgment or allegation of patent
+infringement or for any other reason (not limited to patent issues),
+conditions are imposed on you (whether by court order, agreement or
+otherwise) that contradict the conditions of this License, they do not
+excuse you from the conditions of this License. If you cannot
+distribute so as to satisfy simultaneously your obligations under this
+License and any other pertinent obligations, then as a consequence you
+may not distribute the Program at all. For example, if a patent
+license would not permit royalty-free redistribution of the Program by
+all those who receive copies directly or indirectly through you, then
+the only way you could satisfy both it and this License would be to
+refrain entirely from distribution of the Program.
+
+If any portion of this section is held invalid or unenforceable under
+any particular circumstance, the balance of the section is intended to
+apply and the section as a whole is intended to apply in other
+circumstances.
+
+It is not the purpose of this section to induce you to infringe any
+patents or other property right claims or to contest validity of any
+such claims; this section has the sole purpose of protecting the
+integrity of the free software distribution system, which is
+implemented by public license practices. Many people have made
+generous contributions to the wide range of software distributed
+through that system in reliance on consistent application of that
+system; it is up to the author/donor to decide if he or she is willing
+to distribute software through any other system and a licensee cannot
+impose that choice.
+
+This section is intended to make thoroughly clear what is believed to
+be a consequence of the rest of this License.
+
+ 8. If the distribution and/or use of the Program is restricted in
+certain countries either by patents or by copyrighted interfaces, the
+original copyright holder who places the Program under this License
+may add an explicit geographical distribution limitation excluding
+those countries, so that distribution is permitted only in or among
+countries not thus excluded. In such case, this License incorporates
+the limitation as if written in the body of this License.
+
+ 9. The Free Software Foundation may publish revised and/or new versions
+of the General Public License from time to time. Such new versions will
+be similar in spirit to the present version, but may differ in detail to
+address new problems or concerns.
+
+Each version is given a distinguishing version number. If the Program
+specifies a version number of this License which applies to it and "any
+later version", you have the option of following the terms and conditions
+either of that version or of any later version published by the Free
+Software Foundation. If the Program does not specify a version number of
+this License, you may choose any version ever published by the Free Software
+Foundation.
+
+ 10. If you wish to incorporate parts of the Program into other free
+programs whose distribution conditions are different, write to the author
+to ask for permission. For software which is copyrighted by the Free
+Software Foundation, write to the Free Software Foundation; we sometimes
+make exceptions for this. Our decision will be guided by the two goals
+of preserving the free status of all derivatives of our free software and
+of promoting the sharing and reuse of software generally.
+
+ NO WARRANTY
+
+ 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY
+FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN
+OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES
+PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED
+OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS
+TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE
+PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING,
+REPAIR OR CORRECTION.
+
+ 12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING
+WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
+REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES,
+INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING
+OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED
+TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY
+YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER
+PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
+POSSIBILITY OF SUCH DAMAGES.
+
+ END OF TERMS AND CONDITIONS
+
+ How to Apply These Terms to Your New Programs
+
+ If you develop a new program, and you want it to be of the greatest
+possible use to the public, the best way to achieve this is to make it
+free software which everyone can redistribute and change under these terms.
+
+ To do so, attach the following notices to the program. It is safest
+to attach them to the start of each source file to most effectively
+convey the exclusion of warranty; and each file should have at least
+the "copyright" line and a pointer to where the full notice is found.
+
+ <one line to give the program's name and a brief idea of what it does.>
+ Copyright (C) <year> <name of author>
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; if not, write to the Free Software
+ Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+
+
+Also add information on how to contact you by electronic and paper mail.
+
+If the program is interactive, make it output a short notice like this
+when it starts in an interactive mode:
+
+ Gnomovision version 69, Copyright (C) year name of author
+ Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'.
+ This is free software, and you are welcome to redistribute it
+ under certain conditions; type `show c' for details.
+
+The hypothetical commands `show w' and `show c' should show the appropriate
+parts of the General Public License. Of course, the commands you use may
+be called something other than `show w' and `show c'; they could even be
+mouse-clicks or menu items--whatever suits your program.
+
+You should also get your employer (if you work as a programmer) or your
+school, if any, to sign a "copyright disclaimer" for the program, if
+necessary. Here is a sample; alter the names:
+
+ Yoyodyne, Inc., hereby disclaims all copyright interest in the program
+ `Gnomovision' (which makes passes at compilers) written by James Hacker.
+
+ <signature of Ty Coon>, 1 April 1989
+ Ty Coon, President of Vice
+
+This General Public License does not permit incorporating your program into
+proprietary programs. If your program is a subroutine library, you may
+consider it more useful to permit linking proprietary applications with the
+library. If this is what you want to do, use the GNU Library General
+Public License instead of this License.
Index: /ethereal/plugins/sbus/Makefile.am
===================================================================
--- /ethereal/plugins/sbus/Makefile.am (revision 0)
+++ /ethereal/plugins/sbus/Makefile.am (revision 0)
@@ -0,0 +1,44 @@
+# Makefile.am
+# Automake file for Ethereal/ACN
+#
+# $Id: Makefile.am 11400 2004-07-18 00:24:25Z guy $
+#
+# Ethereal - Network traffic analyzer
+# By Gerald Combs <gerald@xxxxxxxxxxxx>
+# Copyright 1998 Gerald Combs
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License
+# as published by the Free Software Foundation; either version 2
+# of the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+#
+
+INCLUDES = -I$(top_srcdir)
+
+plugindir = @plugindir@
+
+plugin_LTLIBRARIES = sbus.la
+sbus_la_SOURCES = packet-sbus.c moduleinfo.h
+sbus_la_LDFLAGS = -module -avoid-version
+sbus_la_LIBADD = @PLUGIN_LIBS@
+
+# Libs must be cleared, or else libtool won't create a shared module.
+# If your module needs to be linked against any particular libraries,
+# add them here.
+LIBS =
+
+CLEANFILES = \
+ sbus \
+ *~
+
+EXTRA_DIST = \
+ Makefile.nmake_______________________________________________ Ethereal-dev mailing list Ethereal-dev@xxxxxxxxxxxx http://www.ethereal.com/mailman/listinfo/ethereal-dev
- Follow-Ups:
- Prev by Date: Re: [Ethereal-dev] Problems linking ethereal-0.99 on solaris 8
- Next by Date: [Ethereal-dev] win32 dll debugging
- Previous by thread: Re: [Ethereal-dev] Problems linking ethereal-0.99 on solaris 8
- Next by thread: Re: [Ethereal-dev] Re: Patch for new dissector plugin for Ether-S-Bus telegrams modified (Jaap Keuter)
- Index(es):
