By default, Wireshark’s TCP dissector tracks the state of each TCP session and provides additional information when problems or potential problems are detected. Analysis is done once for each TCP packet when a capture file is first opened. Packets are processed in the order in which they appear in the packet list. You can enable or disable this feature via the “Analyze TCP sequence numbers” TCP dissector preference.

For analysis of data or protocols layered on top of TCP (such as HTTP), see Section 7.8.3, “TCP Reassembly”.

TCP Analysis flags are added to the TCP protocol tree under “SEQ/ACK analysis”. Each flag is described below. Terms such as “next expected sequence number” and “next expected acknowledgement number” refer to the following”:

TCP ACKed unseen segment

Set when the expected next acknowledgement number is set for the reverse direction and it’s less than the current acknowledgement number.

TCP Dup ACK <frame>#<acknowledgement number>

Set when all of the following are true:

TCP Fast Retransmission

Set when all of the following are true:

Supersedes “Out-Of-Order” and “Retransmission”.

TCP Keep-Alive

Set when the segment size is zero or one, the current sequence number is one byte less than the next expected sequence number, and any of SYN, FIN, or RST are set.

Supersedes “Fast Retransmission”, “Out-Of-Order”, “Spurious Retransmission”, and “Retransmission”.

TCP Keep-Alive ACK

Set when all of the following are true:

Supersedes “Dup ACK” and “ZeroWindowProbeAck”.

TCP Out-Of-Order

Set when all of the following are true:

Supersedes “Retransmission”.

TCP Port numbers reused

Set when the SYN flag is set (not SYN+ACK), we have an existing conversation using the same addresses and ports, and the sequence number is different than the existing conversation’s initial sequence number.

TCP Previous segment not captured

Set when the current sequence number is greater than the next expected sequence number.

TCP Spurious Retransmission

Checks for a retransmission based on analysis data in the reverse direction. Set when all of the following are true:

Supersedes “Fast Retransmission”, “Out-Of-Order”, and “Retransmission”.

TCP Retransmission

Set when all of the following are true:

TCP Window Full

Set when the segment size is non-zero, we know the window size in the reverse direction, and our segment size exceeds the window size in the reverse direction.

TCP Window Update

Set when the all of the following are true:

TCP ZeroWindow

Set when the receive window size is zero and none of SYN, FIN, or RST are set.

The window field in each TCP header advertises the amount of data a receiver can accept. If the receiver can’t accept any more data it will set the window value to zero, which tells the sender to pause its transmission. In some specific cases this is normal — for example, a printer might use a zero window to pause the transmission of a print job while it loads or reverses a sheet of paper. However, in most cases this indicates a performance or capacity problem on the receiving end. It might take a long time (sometimes several minutes) to resume a paused connection, even if the underlying condition that caused the zero window clears up quickly.

TCP ZeroWindowProbe

Set when the sequence number is equal to the next expected sequence number, the segment size is one, and last-seen window size in the reverse direction was zero.

If the single data byte from a Zero Window Probe is dropped by the receiver (not ACKed), then a subsequent segment should not be flagged as retransmission if all of the following conditions are true for that segment: * The segment size is larger than one. * The next expected sequence number is one less than the current sequence number.

This affects “Fast Retransmission”, “Out-Of-Order”, or “Retransmission”.

TCP ZeroWindowProbeAck

Set when the all of the following are true:

Supersedes “TCP Dup ACK”.

TCP Ambiguous Interpretations

Some captures are quite difficult to analyze automatically, particularly when the time frame may cover both Fast Retransmission and Out-Of-Order packets. A TCP preference allows to switch the precedence of these two interpretations at the protocol level.

TCP Conversation Completeness

TCP conversations are said to be complete when they have both opening and closing handshakes, independently of any data transfer. However we might be interested in identifying complete conversations with some data sent, and we are using the following bit values to build a filter value on the tcp.completeness field :

For example, a conversation containing only a three-way handshake will be found with the filter 'tcp.completeness==7' (1+2+4) while a complete conversation with data transfer will be found with a longer filter as closing a connection can be associated with FIN or RST packets, or even both : 'tcp.completeness==31 or tcp.completeness==47 or tcp.completeness==63'